Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
Hello Team,
I’m working on implementing BLE Mesh on the nRF52832. I extracted the BLE Mesh ZIP file and placed it in the same directory as the nRF SDK. Then, I opened the...
Dear Nordic Support Team,
I am encountering an issue with the nRF52 SDK for Mesh v5.0 and nRF52 SDK v17.0.2 while running the serial example. The system runs for a while...
Hello,
In the header file nrf54l15_types.h, we see the following defines related to the SAADC:
* REFSEL @Bit 12 : Reference control */
#define SAADC_CH_CONFIG_REFSEL_Pos...
Errors on calling "lte_lc_init()"
Does anyone know what the corresponding error codes mean, or what could be done to debug the cause?
Thank you very much.
I am writing an i2s application for the nRF5340 Audio DK with toolchain and nRF Connect SDK v2.9.0.
During development I noticed that nrfx_i2s_start() does not seem to check...
Hi,
I am working on a project where I have two separate physical devices , each based on an nRF52832 :
One device is a BLE Mouse
The other is a BLE Keyboard
My...
Hello, lte_ble_gateway works ok using dk91 or thingy:91 on, v251 - ok v262 - ok but not on, v270 - err v280 - err v290 - err This is straight example code as found in VS....
Hi Team,
I need help currently we are using nrf52833 micro controller, we have problem with external clocks. we want to disable external 32Mhz and 32khz clocks and use only...
I’m using an nRF52840 powered by a coin cell (3V nominal, dropping to 2.3V) and need to read a K-type thermocouple . The challenge is finding an amplifier that:
Operates...
We experience that under some conditions at one moment an already bonded device causes that at the moment of BLE connection the MCU crashes. Possible solution is only to erase...
First of all,I don't study the LOG module yet,just copy & paste from example.
I'm trying to process APP_USBD_CDC_ACM_USER_EVT_RX_DONE event,print debug info to monitor the...
Hello folks,
I'm working on a device that needs a USB storage connection capability. I have put the "mass" sample into my application, and it works as expected except for...
Hi,
we are using the nrf9160 on an addon-pcb as serial LTE-M/NB-IoT modem for our gateway. The host controller is running vanilla Zephyr.
Can someone tell me if I'm wrong...
Hello!
I've been in contact with your sales team in regards to locating the physical BOM of nrf9151, but we've been unable to locate this. I've been - and have directed...
