Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
Hello,
I’m trying to run **LVGL 9.3** on a **nRF52840 DK** with a **2.8" ILI9341 TFT display (SPI)** using **NCS v3.1.0 / Zephyr 4.1 / Toolchain v3.1.0** .
### Problem...
Hello, I want to check the component alignment on the layout.
My layout is different than the reference.
Where should I connect the VNA?
Can I calibrate it on the PCB?
Hi,
I am using a custom nRF9160 board with the nRF7002 Wi-Fi chip via SPI, running NCS v2.9.2 . My goal is to connect to a Wi-Fi network.
However, during initialization...
I want to change the start address of the app in the ESB example from nCS 3.0.2. By default, after compiling and flashing, the program runs from address 0x0. I want to change...
Hi Nordic,
I try to print hello world from promicro(nrf52840).
I am sure board is ok, because I test zephyr 4.2 cdc_acm example on it, and I can see /dev/ttyACM* & console...
Previously, when our NRF5340 was transmitting at a 3ms interval, we encountered issues where the transmission speed failed to meet requirements, with data packets being discontinuous...
Hi Team I was exploring communication with ads1292 over SPI at 1 MHZ. I tried nrf_drv_spi (SPI0_ENABLED in sdk_config.h) api and I was able to communicate with ads1292, however...
I try to do everything as in the guide (second advanced option) devzone.nordicsemi.com/.../small-i2c-oled-displays-using-nrf-connect-sdk but I get errors when building
...
I need to set the connection interval to 7.5 ms. The main.c has the corresponding macro: MIN_CONN_INTERVAL but it seems to me that it supports only integer values...
Please...
When building examples targeting the thingy53/nrf5340/cpuapp board target cmake is run twice, on a fresh build. Then once the build is finished, without modifying anything...
Hi,
In the past we had quite some issues with moist in nRF9160 issues (likely due to bad storage at our PCBA partner). We are now baking all nRF9160 always at 125 degree...
Hi all,
i am currently developing applications for the nrf54L15 for science. We ordered nrf54L15DK and everything is running fine. As we would like to switch to public availabe...
Hi,The Nordic Team
I am developing the Matter over Thread product. I have defined a Bluetooth transport protocol, and now I can receive data. But now I do not know how to...
Hello Nordic Team,
I’m looking to build on a BLE Scanner(Beacon functionality) + Peripheral features on my application using the nRF52810 device, but I’m facing difficulties...
I've been unable to get a SPI MOSI pin to output data on nRF54L15DK using Nordic Connect SDK v3.0.2. SPI transactions report success, and the SCL and CS lines are clocking...
