I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
When i flash i always get the this error: before this i had an another sensor the VL53L0X which worked perfectly.
[0Sensor device not ready! 0:00:00.254,119] <err> VL53L1X...
We are trying to develop a smart controller based on the nRF54L15 that supports a dynamically configurable number of buttons. We want users to be able to select the number...
Hi,
I’m trying to explore the capabilities of DECT NR+ technology using the nRF9151-DK. Are there any recommended external antennas that I would be able to use with this...
Hello,
we are building a custom PCB using the nPM1300. We need a low-noise 1V8 rail for a sensitive analog component and are wondering what the best setup for that would...
I’m working with the CRACEN peripheral on the nRF54L15 and I’m trying to understand the DMA User Tag field used in registers like `CRYPTMSTRDMA.FETCHTAG`.
The documentation...
Hello,
i'm working on a matter sensor on a nRF52840 Dongle and BME280.
The softaware is based on matter/temperature_sensor with config changes to support nRf52840 Dongle...
We are using the Nordic Semiconductor nRF7002-DK . In this board, both PS-Poll and No-PS-Poll power-saving modes are working as expected. However, when running in TWT (Target...
Hi,
we have a issue to find the right configuration to get the maximum throughput in a multiple connection scenario.
In our setup, we are using one central and three peripherals...
Dear Nordic,
We are performing current measurements on a nRF-9151 DK using the Power Profiler Kit II. The attached picture shows the 9151 and PPK-II connected. Notice that...
In the documentation, its suggested that the antenna should have a matching network between the WLCSP NRF52832 and the 50 ohm transmission line that looks like this:
...
Hi nordic：
What is the required voltage ripple range for the nrf52820 when powered at 3.3V, and what is the normal output voltage range for DEC6?
Best Regards！！
jer...
Hello, After receiving thingy91x scanned the QR code on the prototype board i get the following message
Connection failed.
The fingerprint you have provided is not recognized...
Hi Nordic Team,
Good week
We like to confirm a few technical details about the NFC-A tag interface on the nRF52840 :
What is the source of the 13.56 MHz carrier...
