I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
Hi, recently testing nrf9160 SMS example, but seems not working in both Send/Receive
I confirm that SMS is valid in my SIM Card, I put it in my mobile phone and verified...
Can you please explain how the %XCOUNTRYDATA command can speed up network selection in a new location? Does the modem perform a general scan on all bands to determine the...
hello , I am working spi with softdevice(i.e., bluetooth). here spi master is nrf52 and spi slave is ad9837. the spi interface code works fine without soft device(i.e.,ble...
Hello, we are developing a keyboard with two types of connections, via USB and Bluetooth using the nRF52833 chip.
We have all the firmware developed in Arduino since it...
Hi,
I am trying to compile the cfb sample as provided in v2.0.0.
my overlay file is as follows
and my prj file
When I try to build, I get the following error...
is there a way to change the target device to nRF52820 (PCA10100) in segger embedded studio? initially configured to nRF52832 when we started our setup (nRF Connect Desktop...
I want to design a general module. Is it feasible to design the schematic diagram in this way?
1.VDDH is powered by external power supply, is that ok?
2.VBUS is powered...
Hi,
We want to check how changing system voltage affects on GPS reception, for that we need to know the RSSI of each satellite the model use.
I know I can get the C2N...
This is in reference to: devzone.nordicsemi.com/.../getting-started-with-nordics-secure-dfu-bootloader
On step B1, it says: " Next step, inside SDKFolder\external\micro...
Hi,
I'm working on a project where the NRF52840 chip is connected to multiple peripherals (4 of them) through SPI. The hardware has been designed in a way that each peripheral...
Hi, I am using the ant_plus/ant_bpwr/bpwr_rx code as a reference to capture power data from an SRM power meter. I am at the point where I get the following messages, which...
Title says most of it. I'm wanting to perform an OTA DFU of an nRF52840 running NCS 2.0.0 using my android from either the nRF Connect Device Manager or nRF DFU app. There...
This is my first time developing for Nordic processors. I am using Zephyr 3.0.99 with the nrf52810 on a ublox BMD-330 eval board. I connected a W25X20CL 2M-bit chip via the...
I've got a working nrf52832 application using central role to connect to another peripheral. I also want to enable SMP DFU mode - so the app needs to advertise and behave...
Hi,
I am using sample code v1.8.0\zephyr\samples\net\sockets\dumb_http_server to test USB RNDIS
I did some changes in overlay-netusb.conf gile lik
# USB Device settings...
