Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi All,
I have designed my custom pcb board for nrf52811. With the Jlink the IC is detected in visual studio code also it gets programmed. But i did not see its working...
Hello,
I am currently working on a project that involves interfacing the TLV493D 3D magnetic sensor with the nRF52832 microcontroller. I would appreciate any guidance or...
Hi
We use the nRF52832 for an NFC device. The device is 99.9 % in the system off state to save power as much as possible. because the device is power by a button cell battery...
Hi
I'am using nRF util version 6.1.7 for a long time to generate a DFU packages. I need to debug my ble data so i thought of using ble sniffer from nrf util. But the ble...
Hello! We have a project under nRF Connect SDK and Zephyr. It uses Bluetooth central and peripheral role (GATT client and server).
The project works good under SDK v2.7...
Hi,
I'm trying to connect to the nRF52840 dongle using nRF Connect for Desktop Programmer v4.5 on MacOS 15.2 so I can update the firmware. The dongle has the red flashing...
I've then tried both the command " nrfutil ble-sniffer sniff --port /dev/ttyACM0 --coded" as well as "nrfutil ble-sniffer sniff --port /dev/ttyACM0 --coded --scan-follow-aux...
Helo,
I lost the PUK to my iBasis SIM, so I can't register it on nrfCloud.com for my 9160. Is there a way to recover it or do I need to buy a new one? (If so, where?)...
I tried to write the following simple '.overlay' file:
However, I am getting the following error:
but if you look inside the .dts files provided by the 'nrf52dk' I...
Hi everyone,
I’m working on a Zigbee application using the nRF52840, and I’ve been experiencing periodic reboots that I cannot figure out how to resolve. I’ve already updated...
Hello. I have a question about the development environment when developing using nrf.
When you build a new board and make firmware without using dk or ek, do you usually...
Hello everybody! There is a problem and help is needed. With the help of hardware timers, I need to generate a signal with a given accuracy. The frequency is 998 Hz. I'm using...
We are working on developing wearable device (like band) with cellular-IoT network connectivity. Considering available features and size, nRF91 series seems to be a good choice...
Hello
I am developing an application in which I am using a timer expiry function to submit an event periodically. My application is using the Application Event Manager...
Hello, when testing the BLE sniffer with an nRF52840 dongle (utilizing the most recent official sniffer firmware), I configured Wireshark to capture the coded PHY. After initiating...
