Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
For our application we are using the nRF9160 and we need low re connection / reset timeouts. Sometimes during a bad chain of events our application will trigger the reset...
Hello, I'm current using the nRF9151 DK, modem firmware version 2.0.2, sdk version 3.1.1.
I built my application on top of lessons 8 and 4 in the Cellular IoT Fundamentals...
Using Zephyr in NCS 2.8 on nrf5340/nrf7002 wifi combo, and trying to get https to work. I'm using the option where the TLS setup is done in the socket layer (enabled in prj...
Hi,
This was a major nuisance for me. As you know from the nRF52832 product spec, the TWI interface is deprecated in favor of TWIM. You may also know that there are any...
I am using the Scanning module in NRF5 SDK v17.1.x to set up a BLE scanner that matches a specific name e.g. 'NordicSemi'. The above string contains 10 characters ( But the...
Hi,
What would be the state of SWD/SWCLK be when the nRF52840 is held in RESET mode?
I am thinking if a simple gang programming be implemented by SWD/SWCLK be shared among...
Hi,
I am trying to run the Zephyr icmsg sample on the nRF54L15-DK. My goal is to establish communication between the M33 core and the RISC-V core.
https://github.com/zephyrproject...
Hello All,
I am having an issue where attempting to follow the quick start for an nRF9151 development board leads to this error:
I have looked at this post , and unfortunately...
Hi, We are seeing some odd behavior when running in the peripheral role connected to a central device. Occasionally, it appears the central device needs to retransmit a packet...
Does the SPIM of nrf52833 support the selection of SS pulse mode? The SPI of STM32 supports specifying the data bit width by the hardware pulling up the chip to select the...
Hello All,
I implemented the HTTPS call to Amazon using the certificate, and the POST request returns the device ID. Like you docs: Exercise 2 - Adding TLS to the HTTP connection...
HI
My current system consists of an nRF54L15 paired with an external flash and sensor. In low-power mode, the current consumption is approximately 15 µA. After sleeping...
Hello! I am facing issues when trying to set up a PPP connection using the Serial LTE Modem (SLM) application on the nRF9151 DK, and I would appreciate some guidance. I am...
Hello,
I have seen many topics regarding the SAADC sampling modes and power consumption trade-offs on DevZone, but none of them clearly address my concerns. I would like...
