Has anyone experience of successful TICK_DV calibration for nRF9E5? What order of accuracy should be achievable?
In my application I maintain a software RTC clocked by...
Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Using a slightly modified version of the Zigbee Light Bulb sample app from the current samples compiled using nRF Connect for VSCode on a Mac and programmed to a nRF52840DK...
Hello,
I started off doing a v3.1.1 build and got this serious warning message
warning: BT_CTLR_DTM_HCI (defined at subsys/bluetooth/controller/Kconfig.dtm:14) was assigned...
This is a bug report for nRF Connect SDK 3.1.1.
The zsock_poll() method and hence also the poll() wrapper method https://docs.nordicsemi.com/bundle/zephyr-apis-3.1.1/page...
When following through the process described on GitHub for the NCS_SERIAL_MODEM I get an error during the build. I am following the steps described in the readme exactly as...
Hello Nordic Team,
We have developed a custom PCB using nRF9151 and nPM1300 . Sometimes, the PMIC powers up and works normally; other times it doesn’t start at all. It occasionally...
Hi All
I have a question here.gatt Characteristic uuid has been Modified After the equipment has been in run for some time.
Current conditions of the equipment:
1.The...
Hi all,
I'm trying to use SPI Slave on a proprietary Hardware that use Ezurio BL54L15 (that contain a Nordic nRF54L15 chip). The environment is VSC + nRF Connect SDK 3.1...
Hello Nordic team,
I’m using the Mikroe nPM1300 PMIC Click Board (based on the Nordic nPM1300 PMIC ) with an ESP32 over I²C to charge a Li-ion battery.
Setup details:...
Hi,
May I know if the ncs add-on sdk-ant also supported nRF52833 because it is not mentioned in the list. Thanks.
Compatibility — ANT for nRF Connect SDK documentation...
Hi,
I need to use GRTC channel 0 in a nRF54L15 project. Channel 0 is special. It is the channel that the INTERVAL register controls. `zephyr/boards/nordic/nrf54l15dk/nrf54l_05_10_15_cpuapp_common...
Hello,
I’m designing a wearable device based on the nRF52832. To maintain time and date when the MCU and other sensors are completely disconnected from the 3.3 V supply...
Hi, I have an issue with nrf52DK, I cannod flash new version of my software. I have an error in VS Code:
* Executing task: nRF Connect: Flash: Aurora-nrf52/Aurora-nrf52...
Hello,
I am using Nordic nRF Connect SDK v3.1.1 and nRF5340DK board. My project is based on the project: GitHub - nordic-auko/nRF5-ble-timesync-demo: nRF52 clock synchronization...
Hi,
Has there any good course or training you recommend developing with LE Audio Development Kit either through Nordic official training or your preferred training program...
