Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I am trying to make a custom board device tree for evaluation of some new parts and am struggling. I have attached the Schematic as reference sine this is only for part discovery...
Hello,
I am developing a product with the nrf52840 + npm1100 for battery management. I added a usb connection for serial communication, connected as suggested by the reference...
NCS 2.7.0
nrf52840
I'm currently porting software that was originally developed for nrf52832 on NRF5 SDK to run on Zephyr. I am currently on a deadline to delivery a prototype...
I am trying to run the sample using NCS v2.5.0. This is what happens on the console when I try to connect from the dongle, when running the Test Procedure:
The discovery...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
Hello,
I recently migrated to SDK version 3.2.0-preview, which supports Matter 1.4.x.
When I use ZAP and add a new endpoint to the light_bulb example under the name Electrical...
Hi I'm trying to communicate with ICM45686 using nRF54H20 and SPI CLK, MISO, MOSI state appear correct but CS pin is not asserting/deasserting following it the scope capture...
Regarding the nRF54L15-DK development board and its use with BlueZ on an Ubuntu virtual machine: After flashing the hci_uart example onto the nRF54L15-DK board, I used the...
I’m working on a project using the nRF54L15 SoC together with the nPM1300 Power Management IC . In my hardware setup:
BUCK2 output from the nPM1300 is connected to the...
Hello, I am facing an issue in nrf52dk (nrf52832dk). Whenever I access i2c0 bus for the controller it works fine but whenever i switched on the i2c1, it starts giving me device...
Hi, I`m working on a custom board. I have been playing around with it for a couple of months, but just recently stumble upon a strange behavior. This is a custom device where...
Hi, I am trying to use the external flash on the nRF54L15 DK with QSPI to perform the zephyr/samples/subsys/fs/fs_sample sample.
I am using NCS v3.1.0 (on Windows if that...
I’m working on a project using the nRF54L15 SoC together with the nPM1300 Power Management IC . In my hardware setup:
BUCK2 output from the nPM1300 is connected to the...
