Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
Hello,
I'm using nRF52833, pca10100..
My project combines the functions of scan and advertising. Each UUID is different and they pair with a different device. I initialize...
Hello, I have got the Acconeer XM122 module (v2.4) and the Acconeer XB122 module (v1.3). The XM122 is connected to the XB122 which is like a breakout board for the XM122....
We customized our own development board based on Nordic's Thingy91 development board. Now it's welded, the circuit works, and we've flash demo MQTT_simple and Asset_cracker_v2...
Hello,
Im a student trying to use the nRF52811 SoC for a project, i need to design a pcb with the chip and a few more things.
I am planning to use the available reference...
Hi,
I need to create a custom dts for a custom board where I need to define the pins used for interfacing to some external devices. The generic "gpio-leds"/"gpio-keys",...
hello Nordic
i have a project than works with nrf52840 and ncs (zephyr)
i want to have the same application running on nrf52832 as well, as part of a single code base...
Hello,
I'm trying to test example "blinky" using nRF52833 board with PCA10100. I used the pca10056 example (10100 don't exist ), and got the "Unknown function at 0x0007521E...
1: The Apple's "Find my function" , How big is the "Find my SDK" ,RAM? ROM?
We can use nrf52820, or nrf52811,or nrf52810 to develop?
We must use nrf52832 to develop Apple...
Hi Nordic Magicians,
I have a couple of general questions when it comes to sending large amounts of data (FAST). Ultimately, I'm looking to transmit data with a throughput...
Hi,
I'm putting together some firmware that takes packets received over SPI and then streams them over BLE. I'm trying to run the BLE at close to 1Mb/s (which is still...
Background:
Custom boards
SDK 15.2.0
SoftDevice: s140_nrf52_6.1.0
Please see previous post / case that was closed and cannot be reopened: https://devzone.nordicsemi...
Hello,
I am using zephyr on a nRF52840 to communicate with a vl53l5cx TOF sensor using I2C. When I use i2c_reg_read_byte() or i2c_burst_read(), the device address is sent...
Does anyone know why I am getting low outliers on battery measurements with the SAADC? I am measuring the battery directly every minute. Every seven minutes consistently,...
HI,
To ensure NRF5340 2.4G rf consistency during mass production, which scheme do you suggest is more suitable （ X2 = 32MHZ 10ppm ）:
1、Offset capacitance C36 C37 placed...
