Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi
I am currently evaluating a 52840-DK (from 2017 I believe) and several 52840 dongles (ordered very recently). I managed to successfully run the light/switch mesh example...
Hello,
I'm trying to port the radio synchronization to a nRF5340. For this i need to use a DPPI group that clear a timer and disable itself for doing the task only 1 time...
I'm getting an undocumented status value back from nrfjprog when I try to program my dev board:
ERROR: command exited with status 3221225477 : nrfjprog --program C:/mdsg...
Hi,
I'm new to Nordic tools and am stuck on getting all the pieces in place. I have:
Mac OS 10.14.6
nRF Connect v3.6.1 Getting Started Assistant
Python 3.6.3
All...
Hey Guys,
Transferring emulated project
Transferring an emulated project to the nRF52810 SoC,
If you have developed your application using the emulated project...
Hello,
I am trying to setup a Project with nrf25840 by using the nRF IEEE 802.15.4 radio driver in multiprotocol mode with ble. ( https://github.com/NordicSemiconductor...
Hii guys ,
I have a customised nrf module based on nrf52810 . I have dumped ble_app_beacon code and it works fine but when i dump ble_app_uart example code then i am not...
Hi
I have a question about peers deleting.
It is saying in documentation about pm_peer_delete:
"Warning Use this function only when not connected to or connectable for...
hi Support team,
I have one problem with window7 system both 32 bit and 64 bit, that the usb cdc driver can not be verified by windows, that software signature is not right...
hi support team,
customer has one question about TWI electricity. in the IIC spec the "tLow " should be more than 1.3 us
however, our chip interface TWI timing " tLow...
Overlapping segments detected at address 520192.ERROR: The hex files cannot be merged since there are conflicts.
should be
Overlapping segments detected at address 0x...
I’m obviously missing something from the information I’ve gathered with respect to designing a co-planar waveguide, PCB 50 Ohm transmission line. The calculations I get differ...
Hi everyone,
I've been working on the firmware for a BLE keyboard, this is my first big project using the nRF5 SDK and everything's been going great so far. I'm using...
nRF5 SDK for Thread and Zigbee v4.1.0 documentation states that only application can be updated over Thread Secure DFU. However, nRF5 SDK for Thread and Zigbee v2.0.0 documentation...
