Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
hi , i'm trying to connet sim800l and neo_6m modules to nrf52840dk using zephyr ,however i can't find any code source to use .,or do i have to creat the code from scratch...
Hello,
As I was using the sample“nrf_dm”(SDK v2.6.1),I wondered how programs were run, how threads were scheduled to give measurements, and how I could learn about this...
Hi, I'm working on nRF5340, NCS v2.6.1, Zephyr v3.4.99. The net core is running the child image HCI RPMsg controller. Th app core is running application and child image mcuboot...
Using the following code block nRF52833(PRX) can receive the data from PTX(nRF24L01+).
But how nRF52833 replies to nRF24L01+ with the ACK packet which includes user...
Hi, in order to reuse the original factory public Bluetooth MAC of nRF5340 based radio module, I had introduced a function that reads the MAC address out of UICR.OTP area...
After enabling Littlefs, I wanted to use a serial port to write files to it. I first tried using mcumgr, but currently encountered some problems. So, I tried to directly read...
Hi all,
I am using nrf SDK v2.5.2 and zephyr. In my application I want to measure a signal frequency coming from a GPIO, I read about the PPI and I thought it was good...
Hey there,
I'm trying to build the `hw_unique_key` sample for a nrf5340dk_app (non NS) with CONFIG_SECURE_BOOT so that its `child_image/b0.conf` with CONFIG_HW_UNIQUE_KEY_LOAD...
Hi,
I used to use the nRF51 with Keil, so not too much experience with new SDK, but I have followed the "nRF connect SDK fundamentals" and "BLE fundamentals".
I am trying...
I downloaded the report from the official website in August 2023, but the client has given feedback that it has expired and they need the most recent one.
I would like to test GPIOE APIs on nRF5340 develop board. But west build generated the following warning message.
Could I use nrfx_gpiote _xxx related APIs ( infocenter...
Hi,
I am not sure how to read from a characteristic which doesnt have notify property in them. I started looking into nrf_ble_gq_item_add() But I am not sure on what parameters...
hi
I am trying to get the nrf7002 dk working, however, when i try to provision the kit using the nrf wifi provisioner app i get an error saying " scanning error received...
Hello,
I'm working on nrf5340 audio bis gateway sample.
The NCS version I use is v2.2.0, I know it's a very old version, but for some reason I can't update to the latest...