I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Hi, my app (nrf9160 ns, on DK 1.0 rev.; ncs 1.6.0 ) needs the port pin P0.14 as digital INput (wired on the arduino header, for a shield!!). But something is blocking it from...
Hi,
I'm writing a decoder for a custom radio protocol and I need to measure the rising and falling edges of a signal with high precision. I'm currently using the COMP peripheral...
Have been trying for hours, and searched through the forums, but no luck yet. Modem firmware doesnt seem to load with the following setup. Downgrading to previous Programmer...
Hello,
NCS1.8.0 Windows10 X64,
periodic_adv had set BT_LE_ADV_OPT_CODED and BT_GAP_ADV_FAST_INT_MIN_2 /* 100 ms */
periodic_sync scan info "Prim: LE 1M, Secn: LE Coded...
Dear Sir,
I got error like '[00:01:44.604,858] <error> app: ERROR 1813 [Unknown error code] at KGJ`hó@h:536871936 PC at: 0x0001505C' and I can't where did it happen, I...
Is SD340 v7.0.1 compatible with nRF SDK 17.1.0? https://www.thisisant.com/developer/components/nrf52832/#tab_protocol_stacks_tab
Reason I ask is on the InfoCenter there...
Hi all,
I'm working on the nrf5340 with a modified mesh light sample and nrf connect sdk 1.7.1
I'm measuring from P0.28 which is also LED1 to the GND.
After programming...
Hello,
I am using nRF5 SDK for Thread v4.1 for thread implementation using nRF52840 SOC. I have used mqtt-sn sleepy publisher as my base example to develop my software....
Hello,
I am struggling trying to make this sample work on my board. I changed my prj.conf file with these lines:
And looking at other questions I discovered that sometimes...
Hi,
Is there any way to make app_usbd_audio_class_rx_start(...) complete the data transfer within the same context, rather than defer to user event
APP_USBD_AUDIO_USER_EVT_RX_DONE...
We have been using nrf connect installers 3.3.0 and now 3.7.0. We have recently seen issues with new users encountering this error when installing 3.7.0. Are there any solutions...
Hi,
I started to evaluate the Instaburst feature. I use light_switch_client example, but I am unable to provision the device once I enable this feature.
Below are the...
We are in the early phase of architecting a product that uses BLE and a proprietary RF protocol using the nRF52840 and are considering the addition of the nRF21540. In sifting...
I am currently trying to create a simple BLE observer which listens to advertisement broadcasts from a specific device (given via address). I attached the source code below...
Hi,
SDK - 17.1.0
I want to store my sensor data to the internal flash memory of nRF52810 for a long time. I have some questions here:
The data sheet says the flash...
