Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hello,
I'm trying to work through exercise 2 of the Nordic Developer Academy. It has me using the Blinky Sample. When I add a build configuration I get an error. I have...
The board is nrf52840 based using mcuboot via usb, mcuboot can be activated using a switch, and is indicated via a led, all setup via device-tree, so no legacy here. Software...
Hi,
I am trying to connect nrf9160 to CMW500 callbox however I am not able to connect to it. Switching to a commercial sim card I was able to connect to the network. I am...
We are finding an issue where after a network is running for a while we are unable to interact with devices beyond connecting to them via the nRF Mesh App. Specifically, we...
HI,
I found that nrf Desktop (v2.9.0 nrf54L15) surport fwupd support, it's same with old mcuboot DFU? and i want to upgrade from SPI, how can i do? is there any demo code...
I have a few questions about the sample source of nRF5340 Audio.
1. Where does the connection processing between the Gateway and Headset take place?
2. Where is the BLE...
https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-5-serial-peripheral-interface-spi/topic/exercise-1-10/
spi frequency is 1000000 in DTS...
My company is working on a project that uses the nRF53 that needs to wirelessly send out data roughly every 3ms (via ESB). We are now at the point where power needs to be...
In nrf5340 audio application( SDK2.9.0), I try to set phy to 1M in CIS( 1 gateway,2 headsets).
I made these changes：
Add in prj.conf:
In C:\ncs\v2.9.0\zephyr\include...
Hi! I am trying to get the samples "Bluetooth: Direction finding connectionless locator" and "Bluetooth: Direction finding connectionless beacon" to work on nRF54L15dk. I...
Hello,
I'm working up an application where tens of kilobytes are sent via bluetooth to a device which then stores the data on the internal flash (nrf52832). I've worked...
I want to change the Tx power in nrf5340 audio application.
I add CONFIG_BT_CTLR_TX_PWR_PLUS_4=y to prj.conf, but the power didnt change.
How to increase the power ...
I am developing a new custom board using thingy53 as a reference design. The way I programm my thingy53 now is to use the SWD debug interface with a nRF5340 DK. I understand...
Different boards with the same layout have different power consumption when using NRF54L15.
The circuit board layout myself is used for locator tag development.
broadcast...
