Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Hello, I would like to know if the Power Profiler Kit II could be used to measure current consumption on the Thingy:91 ?
In the Thingy:91 documentation, it is suggested...
I want to add a simple GPIO pin that act as output pin, in the peripheral_uart example .
in main.c
#include <drivers/gpio.h>
//#define GPIO0_LABEL DT_PROP...
I'm using ble_app_uart_c project in nRF5 SDK 17.1 with SES.
I got 2 different devices, one is ARC EM9D AIoT DK (as Peripheral) and another is nRF52840(as Central).
I was...
Hi,
nRF9160 with SLM NCS v1.9.1 fails to attach after 7th RESET (by RESET pin) & attach without power cycle.
There is not any ERROR state reported by modem, modem fails...
Hi All,
I am using s112_nrf52_7.2.0_softdevice with nRF5_ SDK_17.1.0 and Segger Embedded studio for nRF52805.
My application code is successfully patched for nRF52805...
Hi,
I'm using the default software to check the acceleration values when there is a movement in the Thingy:91 on the LTE Monitor terminal.
The document says that this...
Hi,
I want to test of MQTT communication with nb-IOT network before going for development.
For that I have updated pre-built firmware on development board using nRF...
Hi,
I'm using nRF52840DK with a UART peripheral (on SDK 17.1). I'm wondering what's the right way to handle UART error. Every time the peripheral power cycles, I'll get...
Hi,
Getting this error using the latest version of pc-ble-driver-py on Mac with the latest version of Catalina for the example application heart_rate_collector from the...
Hi I've been trying to get into Nordic's ecosystem using their SoCs but it's been a huge headache. Probably because they don't have their own IDE (like Microchip and STM have...
I have looked at few previous posts regarding integrating ble hid mouse and ble hid keyboard. But of no use, still stuck.
I have seen the following posts already
1) https...
In my device that uses NBIOT I am modifying the FW to use LTEM.
During the tests I have shown that the consumption of LTEM transmission for the same amount of data sent...
Hello, I'm looking for a BLE module with its integrated antenna that works with NRF5340 so far i didn't find something using Nrf5340 other then the UBlox Nora B-106 All the...
In my application I need a reliable BLE link between peripheral (in this case based on a nRF52840) and a PC / Laptop. I need to stream data at a rate of 200kbps with a very...
Hello, I'm working currently on an nrf52805 module and I'm creating a board with it, for now, I managed to do the ble app uart for this module and improve to code a little...
