I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
After reviewing the nRF7002 datasheet and reference design guidelines, we were unable to find the input/output characteristics and voltage ranges for PALDO, VDD_BUCK, PWRIOVDD...
Current Setup
I'm currently setting TX power during advertising using the following code:
This successfully sets TX power during advertising, but I need help with additional...
I have been reviewing the datasheet of the BLE audio nRF5340. It lists multiple power rails in power section.
Is any power-on sequence required for the SOC.
Also, can...
All of the following used the same power supply to power our development board and measure the current of the development board: The PPK2 I purchased measured an average current...
Hello,
I have connected the nRF52840 DK to the nPM1300 EVK , with the DK powered from BUCK1 output of the nPM1300.
When I supply 3 V or higher to the VBAT pin of the nPM1300...
Hi,
I’m evaluating the NUS (Nordic UART Service) as a way to stream and receive byte arrays.
I’ve noticed that there are two different implementations of the NUS service...
Affecte d SDK : n RF Connect SDK v 3.2.0 (Zephyr v 4. 2.9 9)
File : z ephyr/drivers/i2c /i2c_nrf x_twi.c
Description
The I2C TWI driver always returns - EIO for every...
I have been reviewing the datasheet of the BLE audio nRF5340. It lists multiple power rails in power section.
Is any power-on sequence required for the SOC.
Also, can...
Using NCS 3.1.0 - getaddrinfo with "offloaded sockets" (nrf9160/51) and ipv6 results in struct sockaddr_in6, where some "c struct padding bytes" (the last 3 of 24 bytes) are...
I flashed the thingy91x using NRFCloud connect. Provisioned it in nrfcloud using hologram SIM cards. How do I turn on air quality and all other sensor information?
ZBOSS NCP: ZBOSS NCP Serial Protocol, Version 1.5 states that a "Full featured Zigbee PRO r22 platform is provided".
Is a more recent version of this document available...
New project using Nordic platform and I need to send multiple commands (32bit fixed size) to a device quickly using SPI with the CS toggling between each. I just want to confirm...
Hi Nordic Team,
I am currently developing a commercial product using the nRF Connect SDK (NCS) . The system consists of several nRF52 peripherals and a PC-based application...
On the nRF9151dk, the transmission line coming from the nRF9151 starts with a 0.1 mm trace width and a 0.46 mm gap, which corresponds to a 50 Ω characteristic impedance. However...
Hi,
using nrf connect SDK v3.1.1
using nrf54L15 development board.
I am trying to run a simple button event yet callback is not fired when
CONFIG_PM_DEVICE_RUNTIME...
