Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi Team,
I am working on NRF52832 based on the BLE mesh protocol here I am using the Light_switch example of SDK - nrf5sdkformeshv500sr
Here I transfer boolean(0 and...
Hi, I'm developing an application based on ble_app_uart, and integrate FOTA is the last feature. I'm using sdk16, S140, nRF52833. I plan update firmware over BLE, so I have...
We've a custom board which has NRF52833 and TM52F1376-MTP-C3. They are connected over UART.
What I want is transfer binary data between Phone and nRF52 over BLE.
and then...
Hi Nordic team,
I'm going to start new BLE application project, so I tried to understand how to use nRF52 series first.
I completed the academy and I'm trying to make...
I am attempting to compile the peripheral_uart example targeting nrf52840dk, I've done quite a bit of work with zephyr but never with the nRF Connect SDK. I've encountered...
Dear Nordic,
There is an issue with simultaneous RTT shell and logging on nCS 2.0.0, please check the screenshot.
Althougth CONFIG_LOG_BACKEND_RTT_BUFFER=1 setting is...
New to Zephyr it has been reasonably straightforward building the UDP sample application to enable an nRF9160 dev board to send and receive UDP messages via NB/IoT to/from...
1. I want to run asset_tracker_v2 in thingy91 kit.
2. I want to interface two UART external devices to thingy 91, may the pins of nRF52840 be used ? if yes, in asset_tracker...
I followed this page in the section "Program application using nRF Connect Programmer", and tried to program my nRF5280 Dongle in Windows.
Like below, then I clicked "Write...
Dear Support Team，
I downloaded the code from github.com/.../ble_app_uart__saadc_timer_driven__scan_mode , modified the file, and burned it to 52832. After running the program...
Hi,
we need a firmware for the nRF52840 to do a function test for the EMC approval test. The test must show that the BT connection still works. It should also show if the...
Hi! I am using the following setup to run the "ble_app_uart" example:
nRF5 SDK 17.1.0
BMD 360 EVAL Board (nRF52811)
SEGGER Embedded Studio V6.32a
I selected the...
Hi ,
I am using BMD 330. Able to flash my working code using Segger.
Post flashing it gets into a loop in the following code
<sym_PAD7XREQQORPXRJMXMW2EYVS4S43S42A5D43SBA...
Hello,
Every time I restart the power(power on reset) and then use the command nrfjprog to download, the following error will appear
After I use the nrfjprog --recover...
