Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
Hi, dear Nordic & all：
When I run libuarte example，I found a problem， I just set P0.14 to high at the begin of mian function, then I send data and test the example's function...
Hello,
I'm trying to develop an application sending GPS over HTTP requests.
I started from the "https client" and "agps" samples in the NRF Connect SDK: the single examples...
Hi,
I'm trying to build secure bootloader DFU(non_debug_version) for PCA10040 with the below mentioned prerequisites and I'm able to build the bootloader successfully...
Hello,
I am using nrf52832 chip and SDK 17.0.2 (Softdevice 7.2.0).
I set the MAC Address as random static as shown below (only relevant parts shown):
ble_gap_addr_t...
We are an educational institution and were hoping to use these in a class integrated with LabVIEW. When we load this up on a faculty desktop and run a simple program, it works...
SDK: 15.3.0 SoftDevice: S132 Device: EYSHJNZWZ (nRF52832)
My device is a peripheral. I want to connect with two smartphones. At that time, I want to connect under the following...
SDK: 15.3.0 SoftDevice: S132 Device: EYSHJNZWZ (nRF52832)
My device is a peripheral. Is it possible to connect two centrals at the same time? I think peripherals can only...
What exactly does the power management library? Does it handles all the ongoing processes and shut them down?
Because I did a test with for instance a flash write, and I...
Hi, I want to use TrustedFirmware-M as a secure backend for an application that uses Mbed TLS in the non-secure domain, and this seems to be artificially limited - the MBEDTLS_USE_PSA_CRYPTO...
Hi All,
I am developing one device using nRF52840 based on Zigbee protocol.
Currently I am using nRF52840 Dev-kit and nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8.
...
Hello,
as discussed in the email with Joakim T., could you please provide us a sample of how to use AT command %KEYGEN to generate CSR using the ECC private key? If you...
I am using NRF52840 with SDK15
I am using AES 128 Encryption and am confused on the documentation:
During the encryption operation with nrf_crypto_aes_crypt or nrf_crypto_aes_finalize...
Hello everybody,
I'm currently trying to create a Bluetooth Low Energy Mesh network of multiple nodes that I can control using a Bridge application.
I use a nRF52840...
Hi,
we are developing one prototype where we are using two MCU for different task. we are planning to give common reset button (for customer access) for both the MCU using...
Hello,
I am attempting to create an example project of the Asset Tracker using the NRF9160DK.
I have installed SES using the Toolchain Manager.
I have attempted using...
