The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hi, I want to store some personal data through flash in the LPN mesh routine. I read some posts and can be implemented by using flash manager, but I can't find the relevant...
Hello, I am working on storing words to flash using fds. I am working with the nRF52 DK and SDK V15.2.0. As mentioned in my earlier post , I am storing some critical state...
Hi,
Greetings!
I am using below setup:
SDK: v16.0.0
Mesh SDK: v4.0.0
Application: Light switch server and client
Hardware: nRF52DK
Distance between client and...
Hi, I am using ble_app_uart example for peripheral device and it will be powered by a 3.7 V battery. I need to use battery as long as possible. So I decided to make peripheral...
When I put the device into sleep it draws app 30 uA in sleep mode. Read in the manual: "Core standby current= 50 μA", "Current drawn if HFXO is forced on through for instance...
Hi,
I am trying to emulate a vendor's tool, whose BLE properties are configured as follows: Custom 128 bit Service UUID like XXXXXXXX- 0000 -XXXX-XXXX-XXXXXXXXXXXX
Custom...
hi, I am working nrf52832. I am making configuration file for nrf52.so I want to used Led3 set as high.
#define LED3 ((GPIO_PIN_CNF_SENSE_High << GPIO_PIN_CNF_SENSE_Pos...
Hi, I am looking to access nRF9160 modem via I2C. Essentially looking for hooks/ serial interface hand-off points used for instance in AT Client sample or Serial LTE Modem...
We have some devices out in the field with a mixture of application versions. In one particular case, we have device A on application version 10 and we have device B on application...
Hi there
I am having issues to perform disconnections from my central device when calling sd_ble_gap_disconnect()
most of the time I am able to disconnect properly using...
Hi Devzone:
I am researching how to maximize radio performance and stumbled on a statement on page 356 in the spec:
"Typical sensitivity applies when ADDR0 is used for...
Hi! Currently I have a nrf52840 devkit hooked up to an SD-card for storage through FATFS (using SPI). I would like to add a BME680 environment-sensor to the board and have...
1. I am trying to connect one node (say node A) from two android phones say phone A and phone B. The node A is configured as an on-off server for lamp 1, but it could not...
Hi
I am working on a project which needs to be developed on FreeRTOS, I am facing an issue i need logs at backend using RTT as my both serial_uarte are being used for communication...
