Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
Hi,Team,
I am developing Pawr using nrf54l15-dk.
For the Pawr example I refer to E:\NCS\v2.8.0\zephyr\samples\bluetooth\periodic_adv_rsp and periodic_sync_rsp.
Regarding...
Hi everyone,
I'm new to Nordic development and currently working with a custom board based on the BC40C module (using an nRF5340). I’m facing an issue with the Bluetooth...
I’m working with nRF9151 + Toolchain 2.9.0 and wanted to share my experience & issue while sending ~7kB data over UART. I’ve tried both DMA & FIFO-based approaches — here...
I am designing a wireless sensor pcb with the nRF52840. I am essentially following the Circuit configuration no. 4 schematic for QIAA aQFN73 from the datasheet to a tee (schematic...
Hello,
I have bought a couple of Nordic NRF54L15 DKs, and it seems that the distance measurement toolbox that was compatible with the NRF52 series is not supported in...
We have nRF54H20DK (rev. 0.9.1), SDK: v2.9.0-nRF54H20-1 and the same Toolchain, IDE: VSCode + nRF Connect plugin
We need to control the GPIO LEDs from two cores ( P9.00...
Hello, as the 32.768khz PPM of our product is out of the range, so i need to fine tune the C1/C2, now C1 and C2 are 22pF, is it in range? what is the range for C1 and C2,...
So i am currently referring this ticket and from that I get to know that when when setting parameters for create config (HCI_LE_CS_Create_Config) command for channel sounding...
Hi,
I’m currently working with the nRF52840 DK configured as a BLE Central device. The peripheral device is a Flutter-based mobile application acting as a BLE Peripheral...
I'm having trouble porting my project from the older SDK (2.6.0) to the new SDK.
I thought the most straightforward way to do that would be to start with a sample project...
I am developing a Bluetooth Low Energy (BLE) application based on Channel Sounding (CS) using the nRF Connect SDK v3.0.2 on ME54BS01 modules from Minew Semiconductor (powered...
Hello DevZone,
Our team has been working on a customized firmware solution that has been flashed onto the nRF52840 DK to meet specific requirements.
We’ve noted that the...
Hi everyone,
I wanted to share an update on the BLE issue I’m experiencing with the BC40C (nRF5340) module on my custom PCB. I initially described the problem in this ,...
