Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
Hello,
I've modified(added custom libraries) an existing example project from the SDK(v 15.3), and I'm trying to build and flash it.
The project compiles fine, but throws...
Hi,
I am using nrf52840 with an ADC that senses data and sends it via bluetooth. I want it to sense data, store it in the memory and then send it via BLE and then start...
Hello,
The current project I am troubleshooting includes an NRF51822 chip. The project includes a boot loader, application hex, and soft device S110 V7.3.0. It was noticed...
When trying to install the nRF Connect app (3.1.0) on a windows 7 machine, it hung up and froze during the Jlink install. After using system restore to go back before that...
Hello we are using SDK 15.3 and SD s140 v6.1.1, we use the cryptocell to do some AES encryption as well as MAC and ECDH.
We noticed that our application was running quite...
Hi,
I'd like to test how long it takes to get a gps signal and send the nmea string via udp. Therefore I took the example 'udp_gps'.
As far as I know the program starts...
Hi,
Is there a tutorial or guidelines on how to send ble-app_hts data to nrfcloud mentioned in this Noridc video below.
Nordic Semiconductor - nRF Connect for Cloud (youtube...
We have an implementation where we need to limit data, and to be able to KNOW how much is actually being sent with the operator, to limit costs.
In a normal Ethernet condition...
Hi Nordic,
I am trying an application where both central and peripheral devices are based on nRF52.
I have to create custom services and characteristics for the same....
Hi, I am beginner for nRF51822. We are using SDK v10 and S120.
We have an IOT Gateway with it's processor interfaced with nRF51822 radio through UART. We have flashed nRF51822...
Hi all, We always have -4Mhz Radio Frequency Interference when using nrf24l01 and nrf52832 chips.We use nrf24l01 as a slave receiver, and use nrf24l01 or nrf52832 as a master...
Hello,
I'm trying to set up my nrf9160 Dev Kit and I'm having problems connecting it to the nrfCloud.
Since I'm using it in Austria, I'm using a different sim card on...
can somebody help me on how to enable twim0..
it was no problem in twi_sensor example...now i am integrating twi_sensor in ble_eddystone...and on built it give an error...
