I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
I get the error message in red when pressing Connect below:
The certificate is downloaded as instructed in the devacademy 4.2.
server_certificate.crt: ...
Hi,
I recently purchased a Thingy91, and here's what I’ve done so far:
Built the firmware
Registered the SIM and device on the cloud platform
Built the Asset Tracker...
I found a related post ( ) where the advice was given to just get a DevKit, which I agree with for development, but my understanding is the nRF52 dongle firmware contains...
MCU : nrf52840
SDK : sdk_17.1.0
Hello, we are developing a product using the nRF52840.
However, we have observed that while the nrf_log_backend_uart~ function is operating...
Dear Nordic support,
I've done some testing to send many data in BLE notifications, and I have a question regarding the BLE stack implementation. We are using NCS v2.6.1...
Hi,
I combined the throughput example and the lbs example in NCS v2.6.2 running in NRF5340DK. It seems the advertisement is not resuming after i disconnect the app (NRF...
I'm trying to install the 2.7.0 toolchain into D:/NCS/ somehow the toolchain manager frequently installs in a different path than the one specificied in the extensions settings...
Hello, guys
I have nRF9151-dk running Serial LTE Modem (SLM) app on it and want to test the ability of working with sockets (open socket, send/receive data, close the socket...
Hi all,
We have designed a custom board including a NRF52805 chip. We also followed PCB design guidelines and used the exact PCB layout recommended by Nordic. As expected...
Hi folks, thanks in advance for your support.
The thing is that in my SEGGER project I didn't have explicitly linked a bootloader to be flashed in the device (nRF52832)...
nRF52832 & NCS v2.6.1
I merged the NUS central and NUS peripheral FW into a single one where the user calls appropriate initialization functions to activate whether central...
Hi,
I am trying to write a simple application that uses I2C on a nrf5340 DK, assigning SCL to P0.9 and SDA to P0.10, using the app core ns . The application builds without...
Hello,
I am working with the nRF9160DK and the Thingy 91 to do some basic evaluation.
I was wondering if these devices supported Private LTE connections.
Thanks.
On Seeed Xiao nRF52840, I'm attempting to use reset (P0.18) as GPIO in a Zephyr (ZMK) app.
I've set
```
&uicr {
/delete-property/ gpio-as-nreset;
nfct-pins-as...
We want to be able to toggle between 128 MHz and 64 MHz on our nRF5340 based custom board depending on whether our audio pipeline is in process or not. However, a note in...
