I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hi!
NCS 3.1 On a custom board with nrf5340 and nrf7002, h ave successfully implemented and tested FOTA over Bluetooth Low Energy with Simultaneous updates for both cores...
Hi,
I'm trying to reduce the power consumption of my Matter Temperature sensor code.
I'm averaging around 90µA of consumption, but I'm confident that can be reduced. ...
Hi,
I’m having trouble getting an ISP1807 (nRF52840) to run on a custom PCB, and I’m hoping someone here might recognize what I’m missing.
Hardware / setup
Module...
Hello, we’re currently facing an issue regarding the start-up of the nrf9151 modem. Its a custom PCB and closely follows the schematic of the nrf9151 DK. For first test SW...
Hello Nordic Engineer,
I know that I can modify #define DEVICE_NAME "device001" in sdk_config.h , but it takes a lot of time to compile and flash the program every time...
Hi,
I have flashed hci_usb example on nrf52840dongle(hci1), enabled DLE. But when linux machine requests data from other board(as sender) dongle is getting crashed.
The...
I have create a model (which is now marked as complete), but when I go to the results tab the options (and below) just show a spinning circle. How can this be fixed?
Unable to start debugging. There was an error starting the pipe program 'JLinkGDBServerCL'. An error occurred trying to start process 'JLinkGDBServerCL' with working directory...
Recently, I’ve been working on the process of switching between BLE and a private protocol. When I switch to the private protocol, I usually need to disable the softdevice...
We are observing an intermittent issue on an nRF9151-based custom PCB where DNS resolution fails after repeated events occurring within a short time window, even though cellular...
Hi,
Sometime ago, the Nordic chatbot (bottom right icon) on this page https://docs.nordicsemi.com/ worked great on my work computer using Edge browser. Now even though I...
Are there any unique design considerations to take into account when using the nRF54L series with RRAM? For example, are there any concerns about magnetic fields causing bit...
Hello,
I’m using **VS Code + nRF Connect SDK v3.2.1** with a **Nordic Thingy:53** board.
I can build firmware successfully, and nRF Connect **Programmer (Desktop app)...
I setup the nrfx logging per the sample and it works within my main.c but when I get a log warning from nrfx_timer.c I do not get an output. Is the logging configurable across...
Hello,
I would like to use the official hci_uart sample to send Channel Sounding test-related HCI commands (specifically HCI_LE_CS_TEST and HCI_LE_CS_TEST_END ) to the...
