Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
On Seeed Xiao nRF52840, I'm attempting to use reset (P0.18) as GPIO in a Zephyr (ZMK) app.
I've set
```
&uicr {
/delete-property/ gpio-as-nreset;
nfct-pins-as...
We want to be able to toggle between 128 MHz and 64 MHz on our nRF5340 based custom board depending on whether our audio pipeline is in process or not. However, a note in...
I am facing a similar issue described in https://devzone.nordicsemi.com/f/nordic-q-a/97084/direct-xip-mcuboot-both-images-have-the-same-version where mcuboot is unable to...
Hi everyone, I'm here to ask if anyone could help me solve the problem I'm having when programming on the nice!nano board. In my project, I created a new board called nice...
I recently purchased an nrf52840 dongle.
In nRF Connect for Desktop (v5.0.2) and with or without the device attached, Programmer (v4.4.1) starts with a rust-panic error...
Hi all,
I'm really new with nrf zephyr environement, so for now I've build a custom board build with nrf9161 (look similar to circuit dojo feather nrf9160). I'm able to...
We would like to change BLE's PHY setting 2Mbps to 1Mbps in Audio profile. In SDK ver2.3.0, we could find BLE's PHY setting as follows;
Let me confirm the point to be modified...
Hi there:
I want to do BLE FOTA on nRF5340 Audio DK board. I have sdk v2.6.2. I'm trying to make the existing audio application work by taking the source code as it is from...
So I am using the NRF5340, and it has been fine for a few months now, however today, it stopped working and sending any data between the USB and laptop, the LED5 flashes once...
Hello!
Any and all guidance on the issue described below would be greatly appreciated! I am happy to provide any additional information.
Thank you for your time, ...
Hello Nordic,
As described regarding BLE Serialization in the link https://nordic-prod.zoominsoftware.io/bundle/sdk_nrf5_v12.3.0/page/lib_serialization.html, we want to...
Hello,
I have developed a custom board for the nrf52840 with the QFAA QFN48 package.
I am trying to program it with my nRF52840, I am using P20 of the DKconnecting the...
I am wondering if someone can help point me to a repo that explains how to create a gpio interrupt that can detect when my CS line goes from High to Low and jump to a method...
I'm evaluating an OpenThread mesh network in a large warehouse and considering the nRF21540 Front-End Module (FEM) for the router devices. To test this setup, I purchased...
Hi,I have been trying to configure two I2S devices where I will read data from mic SPH0645 with NRF5340 then I need to send that data to Amplifier(TAS2563).So,help me configuring...
