Hi Nordic Team,
I've just received my nRF93M1 DK. Similar to this issue, I am unable to get my DK connected using the PPP shell sample.
Hardware: PCA10232 v0.4.0 Modem...
I have an application which is not able to talk with my gas gauge device when the TI EV2400 can. Looking at the waveforms all look the same except for the Zephyr code has...
Is there a recommended way to access the USB data lines from the J3 connector of the nPM1300EK? I would like to be able to charge the battery and also provide a USB mass storage...
Hello,
I am currently testing DECT NR+ communication between multiple nRF9151 SMA DK boards, but I am unable to establish a connection between an FT and a PT.
I initially...
The nRF91 series of modem firmware are distributed with FOTA-TEST diffs to allow for validation of FOTA integrations. Will the nRF93M1 firmware images be distributed with...
Hi Nordic team,
I am using the nRF52840 HCI USB project as the controller firmware, with a Linux device acting as the Bluetooth host.
My application has multiple BLE connections...
Hello DevZone Community,
I wanted to share a unique hardware-in-the-loop implementation using the Power Profiler Kit II (PPK2). While the industry is heavily focused on...
NCS 3.4.0, sysbuild, with mcuboot enabled.
I want to use a simple custom "my.overlay" for both the app and mcuboot.
For the app it works with
-DEXTRA_DTC_OVERLAY_FILE...
I first noticed this when incorrect flags reported by mcumgr when performing network core update
When performing a network core update with CONFIG_SECURE_BOOT_APPCORE enabled...
Hello Nordic community,
using nrf5-sdk for nrf52840 SoC, I followed the uart example as below.
The uart tx and rx works fine BUT NOT THE HWFC
eg. When the CTS is set...
Hi Nordic Team,
Below are the configurations that I have done for the nRF21540 FEM.
.config file
#
# Multiprotocol service layer (MPSL)
#
# CONFIG_MPSL_FEM_ONLY is not...
I have a question regarding the solder balls on the WLCSP package of this device. Are they collapsing or non-collapsing? Can you also provide a definitive source for this...
I have been working on a soil moisture sensor for my indoor plants and I wanted to build some skills in PCB design using a Nordic SoC. I have chosen the nrf54L15 for this...
Hi,
I've been developing the next version of our product with an nRF54L15 There's external SPI flash attached on QSPI via SQSPI which is working ok (albeit it is very slow...
Hello everyone,
I’m currently porting my old projects from NCS version 2.9.0 to 3.3.0.
In doing so, I no longer want to use the outdated Partition Manager; instead, I...
Hi,
I've got two ESB transceivers talking to each other - a PTX on nRF52832 (E73 module) and a PRX on nRF52810 (Holyiot module, the "tag"). Both chips can obviously TX and...
On a recent run of prototypes using the nRF9151 and the nPM1300 we've had a few failure where the nRF9151 cannot connect to the debugger and the board exhibits much higher...
I have two nRF9151 DK boards, both hardware revision 1.4.0, both showing the same SIM detection failure.
Symptoms on both boards:
AT%XSIM? always returns %XSIM: 0,9...
We have purchased a radio fitted with the nRF9160 modem and fitted it with a roaming SIM for NB-IoT use, we are in UK and have Band 20 EE and Vodafone.
What are the initial...
Now my product need FCC, and I use DTM example, only changed the txd,rxd pin in firmware, the lab can use nrfconnect for desktop to enter test, but the tx power is low when...
Dear Nordic,
I'm designing a 0.6mm thick 6-layer rigid-flex with the nRF54L15-CAAA, and due to my current stack-up the ground polygon to trace clearance can only go as small...
