Thanks in advanced. I'm immigrating projects into NCS bare metal v2.0.1. Sample Bluetooth ble_nus only advertises for 3 minutes, then device can't be scanned again. I check...
Hello,
I'm following online courses in Nordic Academy (nRF Connect SDK Intermediate).
As indicated in the first lesson,first excercice, I added device_message_queue...
nRF54LM20 + nRF7002, NCS 3.4.1: SoftAP provisioning and station low power in one image
Our battery-powered product (no BLE antenna), removed due to space in the PCB and...
Hi
Have you done any benchmarking to estimate the difference in power consumption when comparing the nRF9151 in NTN mode vs LTE-M?
In particular I am curious if NTN has...
Hello.
When I ran the NCS SBOM command using VS Code, the following error occurred, and the file could not be generated.
I would appreciate it if you could tell me how...
Setup
- Programmer: nRF54LM20 DK (PCA10184), debug out header P13 to an external board over a 10-pin ribbon under 10 cm, SWD0_SELECT grounded on the target side. The DK...
I created software and flashed successfully to the nRF54L15-DK. It is to toggle an LED on and off on P2.09.
#include <zephyr/kernel.h>
#include <hal/nrf_gpio.h>
...
hi support team,
our customer is trying to use gpio to simulate interface for external device communication.
and i tested our 5340dk pin 28 and pin 29, find out that gpio...
Hi,
I have a very basic question:
Where to find the sample source code mentioned in the infocenter of this link ?
infocenter.nordicsemi.com/.../uarte_rx_double_buffered...
I'm using arm-none-eabi-gcc from Fedora linux repositories. It got updated to version 12, and now it's not possible to compile the SDK - there is a problem with linking. It...
Hi,
I am using nrf_mesh_switch_client example and implemented disabling mesh on timer basis,
I have initialized the timer and started it in start() function. The following...
Hi,
I am using SDK 1.9.1 and nRF5340.
Scenario
I am investigating the following scenario:
files containing the firmware upgrade for the app and/or net cores will...
Hi there,
I'm currently using the nRF52 DK (PCA10040) and nRF5 SDK 17.1.0.
Our device needs to permanently connected to a battery, only wake up on a button press and then...
I came across a document called
2870.Measuring_distance_with_Nordic_Distance_Toolbox_slides.pdf
(found here )
Several questions
1. There are 2 slides for "High Precision...
Hi,
I tried every configuration options one by one to change the MTU size, but it doesn't work.
I connect to nRF52840 with Raspbery Pi and when I subscribe to a notification...
Dear All,
I am trying to figure out the maximum current consumed during the NFC operation.
I am using nRF52832 and writable_ndef_msg example from the SDK (LED, flash write...
My previous post and the response I got was hugely helpful to my understanding ESB on the nRF52. Now that I grasp the basics, I felt it was appropriate to create a new post...
Hi,
quick question..Which, if any, Nordic device has NFC that can be read and write without additional NFC ICs?
I've got an NRF52840 dev kit but apparently it only supports...
To the kind attention of Nordic support team,
we are (re)working on an old legacy project using nRF24LU1 and gazell protocol. We would need to know if there is some simple...
I am trying to add this ultrasonic sesnor driver ( inductivekickback/hc-sr04: Zephyr RTOS driver for HC-SR04 Ultrasonic Ranging Module (github.com) ) and testing it with the...
Hello! This is my problem.
SDK：SDK17
Softdevice : S140
Board: nrf52840
The connect interval is 135ms. But the latency I test is larger than connect interval. So...
i use 2x nRF52840 DK as DUT and Lower tester and DUT, my windows laptop as the Upper tester, and use python code from nan_34 Setting up production test using DTM.
as below...
