Hi,
I am currently testing the dect_shell example on two nRF9151 DKs and achieved a range of ~500m. I want to transition this setup into a multi-hop mesh network topology...
Hi: The device shows successful reconnection, but the mobile end is not connected.
And the connection information displayed on the device is (public), which is actually...
I am trying to measure the 300mA system current.
I cut off the system lane and connected Vin, Vout.
And when in ampere mode, the system is not turning ON.
(When I replaced...
Hi Nordic,
I have a custom board using a Raytac MDBT53 module with nRF5340. The board is designed for 3.3 V / LDO mode, but during bring-up I likely flashed firmware/configuration...
Hello Nordic support,
I am using two nRF54L15 devices with NCS v3.0.1 and ESB DPL at 1 Mbps. Auto ACK is enabled, the payload is 252 bytes, and the retransmit count is 9...
# SoftDevice Controller assert during DTM receiver test at dead/marginal RF link (nRF52833) ## Summary On an nRF52833, running the nRF Connect SDK Direct Test Mode (DTM) 2...
A customer implemented a nRF52840 (QIAA package) and says the output power is about 10dB lower than expected. Having done multiple nRF52 designs with good results, I reviewed...
Hi, I am developing a SDK 17.0.0 based iBeacon application, and I see below API for initializing/updating advertising data.
I want to know what does it do with the buffer...
Hello
I am now quite familiar with the basic PWM playback capabilities of nRF52832. However, I would like to make a chain of simple and complex PWM playbacks.
I have already...
Hello,
I am developing an application that sends data from an Arduino Nano 33 BLE Sense to a custom Android app (Motorola Edge running Android 10). The Arduino board is...
Hi,
As many of you, I'm tryng to compile pc-ble-driver (v4.1.2) found in https://github.com/NordicSemiconductor/pc-ble-driver/tree/v4.1.2 , just to see how the code works...
Our application stores sensor data in flash and sends the data on request via USB. But if the device is connected to Bluetooth once then it is having issues in USB data transfer...
Hello,
At this point I have been able to successfully customize and run the mcuboot procect.. Mcuboot is successfully built and linked with my app.
However I am would...
Hello
I'm Strangistra and I work on a Adafruit Feather nrf52832.
I have the Arduino IDE 1.8.13 and I use the FastLed library 3.3.3.
I have a strange behavior with the...
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.1.0/nrf/samples/bluetooth/peripheral_lbs/README.html
I'm talking about the above. SW5 switched to nRF52. However...
My team is trying to acess OpenThread CLI over UART0 with the nRF Connect SDK OpenThread CLI sample with our custom board.
We have tested with a Nordic's nRF52840 DevKit...
Hi,
I'm using nRF51 dongle as a sniffer and executing 'nrf_sniffer_ble.bat' file via cmd. I have tried interface commands "nrf_sniffer_ble.bat --extcap-interfaces" based...
I want to download offline documentation , but none can be downloaded. why? for example , on the webpage "https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsds_s140%2FSDS...
I am developing SDK17.0.0 based application with S112.
when I try getting a random value at the end of main, the nrf_drv_rng_rand return err_code=0x05, and it leads to ...
