hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
I am trying to implement GPS code in the nrf9160 but I cant find the function nrf_modem_gnss_init(); to initialize GNSS inside the modem in , is it being initialised within...
The following log is a compilation error.Is there any way to correctly compile?
e:/nordic/ncs/toolchains/fd21892d0f/opt/zephyr-sdk/arm-zephyr-eabi/bin/../lib/gcc/arm-zephyr...
We have an application where response time is critical, and we are trying to minimize the time from advertising to an active channel sounding session.
What we have already...
Dear Nordic,
We are currently evaluating the Amarisoft CallBox as an end-of-line (EoL) testing tool.
In an ideal scenario, we would like to use 1NCE production SIM cards...
When performing FOTA using NCS 2.9.2, we observed that the swap using move process takes approximately tens of seconds. However, with NCS 3.2.4, the same swap using move operation...
nRF Connect SDK v3.2.3, nRF9160.
Hi,
I'm working on a project which has MCUBoot enabled (dual slot) for firmware updates over cellular connection. I did not have a pm_static...
Hello,
I want to program the bare nRF52832 MCU over SWDIO, SWCLK, GND and +3,3V Connections with a Segger J-Link programmer. Unfortunately the programmer could not connect...
Is it possible to be able to get hold of some of the legacy software for the nRF52 BLE sniffer that works off the old nRF Command Line Tool rather than the nRFutil? As I'm...
Hello together!
I am trying to reproduce the ultra low power connection as described in this whitepaper: /cfs-file/__key/communityserver-discussions-components-files/4/3482...
Ultrasonic welding is commonly used to seal plastic enclosures for electronic devices. 32kHz crystals can be damaged by this type of welding and manufacturers recommend not...
Does APPROTECT supersede SECUREAPPROTECT or do both need to be enabled for maximum security?
Similarly, do the HW protections (APPROTECT, SECUREAPPROTECT, ERASEPROTECT)...
I am trying to measure current on a nRF52 DK v3.0.0 using PPK II in source mode.
I cut SB9 and soldered SB12 as described in this guide: https://docs.nordicsemi.com/bundle...
Hello , I 'm trying to use the Lan865x (two -wire eth click ) chip with the nrf52840dk board , using zephyr 3 . 7 . I 'm getting always this error while trying a net sample...
Hello!
I've been trying some of the solutions around these forums but I can't seem to get my nRF52840 DK to show up on my device manager so I'm unable to flash anything...
