But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
~~~~~~~~~~Environment ~~~~~~~~~~ nrf54L15 + NCS 3.1.1 + VSCode + Win11 ~~~~~~~Reproduction Steps~~~~~~~~~ 1. without pm_statics.yml, with following configs (see attachment...
Dear Team,
I am experiencing a weird issue with the firmware on my custom EV board with NRF54L15.
My firmware is using MCUBoot and partition manager (I use a separate...
Dear Team,
I need to switch LXFO to internal RC for MCUBoot, however, I am experiencing troubles configuring it on NCS 3.0.1 (NRF54L15).
If I just add my RC settings to...
Hi,
Our project requires an unusual combination of running BLE, Gazell, and raw radio packets for time sync simultaneously.
Time sync and BLE are infrequent activities...
Issue:
I would like to bring to your attention that I am getting an error when running the 'list command using the nrfcredstore cli utility, while trying to retrieve the...
Hi,
I've run into an issue when doing some compatibility testing between our client's legacy device (802.15.4 transmitter) and the current device in development (802.15...
In the introduction to the bare metal SDK option for the nrf54L:
https://www.youtube.com/watch?app=desktop&v=31znTI-hnCQ
it mentions at around 58:00 that single bank...
I am using nrf connect SDK toolchain version 3.1.1 and nrf connect sdk version 3.1.1 , By default I don't have zigbee related samples/examples and also zboss stack library...
The original question was: "The nRF52840 PS mentions, that this chip contains an ETM but it does not mention the implemented version."
Researching the topic more, I found...
Hello Team,
We have noticed a very weird issue with the nRF5340 Audio DK. After flashing the audio application code given by nordic, everything works perfectly fine. No...
I have asked if I can post this request, ticket number 354361.
Can you help with new research on secure boot?
I am a cyber security researcher at the University of Bristol...
Hi there
I have a question about the way the nRF52 radio handles on air addresses. I currently am developing custom software that uses the nRF52810 radio for a custom protocol...
I’m working with a Manufacturer-Specific Cluster (Attributes) in the Matter Template sample from NCS SDK v3.1.1, and it works fine with attributes. However, when I try to...
Hi, We designed a board using NRF5340-CLAA-R by following the Altium Reference design. Although when we tried to place an order with JLCPCB or PCBWAY, then informed that they...
