This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
We would like to drive two ps/2 interfaces via nrf52840 gpio pins (i.e., reading the protocol bit by bit, via gpio interrupts). A trouble is that ps/2 is timing sensitive...
Hi
I have some questions regarding the 32 MHz crystal on the nRF54L15:
If my firmware is configured to use external capacitors, will the very first crystal startup...
Hi,
I am developing on nRF54L15-DK BM (bare metal) for another board with a different pinout.
I need to disable the the MCUMGR log that prints to UART TX pin 1. 04....
Hi,
I am working on Google fast pair locator tag using NCS sample code. For final product, we need one function in device for certification that is to disable and reenable...
Hi nordic support:
Our product used nRF52840, we tried test nRF52840's BLE OTA RF performance with CMW500. After the nRF52840 device is assembled with the casing, it is...
We have a custom nRF5340 board that interfaces with an MT29 NAND Flash IC over the SPIM3 peripheral. Our DFU solution involves storing update and rollback images on this external...
I'm developing on the nRF54L15-DK using NCS3.1.1. I've recently encountered a strange behavior.
My program writes to the RESETREAS register. A bus fault sometimes occurs...
Hello,
Following the ongoing many issues to make Ethernet work alongside the modem on nRF9160 ( , , devzone.nordicsemi.com/.../ (clicking “Convert to public” on this one...
Hi !
I've been through a lot of documentation but did not find any matching my case.
I'm using a custom board with an NRF9160 chosen for its ability to connect to LTE...
Hello,
I want to use P0.10 and P0.11 for SPI purpose for my custom nrf5340 board.
But when I clear the forwarder property for these pins from the pin editor gui, I am...
Hi Nordic team,
I'm using the nPM2100 PMIC in my design to power a microcontroller. The microcontroller sets the nPM2100 into Hibernate mode , and a vibration sensor connected...
Hi Support:
I am testing channel sounding initiator on our board, but there is a crash on CS initiator starting.
below is log:
uart:~$ initiator on [00:57:24.604,598...
Hello,
The Altium lib provided with the DK, has two geometries, one with an "_2" at the end, what is the difference between these? (if any).
Thank you,
Beleni...
Hello,
I’m using the aws_iot sample with the nRF9160DK-nRF9160 target. When I introduce a bug (calling `net_if_up()` on a wrong interface), the system crashes and halts...
