This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hi Nordic team,
I am working on a custom board based on the nRF54L15 using nRF Connect SDK v3.1.0.
On our hardware, the nRF54L15 has a 32 MHz crystal connected to XC1...
Hi Folks & experts
I hope you ALL are well.
I wanted to share a bring-up result from my XIAO nRF54LM20A workbench and ask for your guidance.
I have the XIAO nRF54LM20A...
Hi folks,
I am working on an nRF52840-based custom board using nRF Connect SDK v3.2.4 and have observed an issue related to runtime power management and PWM.
Environment...
I'm using the prebuilt Aliro stack (libaliro.a, nRF52840), when a session fails inside the library we have no way to get the resulting AliroErrorCode. The stack entry points...
Hi
I'm encountering a problem than the ANT device cannot be scanned. you can use project "ble_ant_app_hrm_v324"(ncs 324）, and modify "
light_rx_open_head" to connect...
Hi Asbjørn，
As I mentioned in case 352770
We are in same question as the initial question issued by our colleague RongLinQin. As I mentioned, we want to conduct BLE OTA...
Hello.
We are developing a project based on the nRF54L15 SoC, utilizing MCUboot, image compression, and TF-M (Trusted Firmware-M). As part of our upgrade from NCS v3.2.4...
Hi!
I am using nRF9151-DK, enabling UART1 and using CONFIG_UART_ASYNC_API.
The build is successful, but the problem every time i connect a flashed kit with this binaries...
I'm trying to get NFC power-up/restart working on nrf54lDK but the call to sys_poweroff() results in: E: ***** BUS FAULT ***** E: Precise data bus error E: BFAR Address: 0x0...
Hi, We are using nRF Connect SDK v3.0.2 (Matter 1.4.1) We are trying to do Matter certification, but we have an issue on TC-RR-1.1 and TC-OPCREDS- 3.1 The device crashes randomly...
We are building a line of product to be used in big size building light management and control.
We believe that both the IV values and a huge quantity of SEQ separate counters...
Hi everyone,
I'm developing a star-topology network using DECT NR+ on nRF9161 DK nodes, running modem firmware mfw-nr+_nrf91x1_2.0.0 (nRF Connect SDK 3.3.0).
My issue...
Hey, I am trying to implement ecdh key agreement and derivation, but I am getting PSA_ERROR_INVALID_ARGUMENT (-135) from psa_key_derivation_key_agreement: Any idea what is...
While debugging the code with Nrf connect extension in VS code , code get stuck at the start only does not go any where getting the SIGNTRAP error continuous
nRF9160 - mfw 1.3.7 - NCS 3.2.4 In my experience, DNS lookup fails with some SIM cards using cloudflare as primary DNS. I wrote to the SIM card provider about that issue and...
