Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
Has anyone experience of successful TICK_DV calibration for nRF9E5? What order of accuracy should be achievable?
In my application I maintain a software RTC clocked by...
Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Hi everyone,
I'm working on a project using the nRF54 and Zephyr RTOS . Previously, I implemented almost identical functionality on an nRF52, where the device consumed around...
hi:
nRF54LM20A_DK board vscode cannot be programmed.
-- west flash: using runner nrfutil -- runners.nrfutil: mass erase requested
-- runners.nrfutil: reset after flashing...
I am writing regarding an issue I am experiencing with two MDBT53V-1M modules (nRF5340) that I have assembled on custom PCBs. Both modules exhibit identical behavior, which...
I migrate an app from NCS 3.1.0 to NCS 3.2.3.
Using mcuboot with a Thingy:91 or Thingy:91X fails.
flash_img_init results in a flash_img_context, which uses ID 2, the application_slot0...
mcumgr disconnecting when i trying to ble dfu .... " Log from nrf connect mobile app"
nRF Connect, 2026-06-16 FYZKS52_E23993 (E2:39:93:7B:81:AA) V 17:16:59.495 Connecting...
We are trying to bring up a new run of an existing PCB design. No changes in the area of the processor, but a different assembly house. The first call inside ble_stack_init...
We're using two nrf54:s, one DK (initiator) and one custom PCB with 2x antennas (reflector)
I've tried adjusting the samples so that multiple antenna paths are supported...
Hi,
I have a question regarding the SAADC timing parameters.
I could not find an official specification for the SAADC power-up time (t_PWRUP). While measuring it on my...
Hi Nordic support:
We previously submitted a case about OTA testing in CMW500 connection mode. Following is that case:
We tried OTA testing with the CMW500 connection...
Hi!
Im creating my own custom board based on the nrf54l15dk board included in zephyr. My board uses both cpuapp and cpuflpr, and has a custom partitioning scheme defined...
Dear Nordic Engineers
I developed a PWM function to drive the RGB LED. Then I found a problem, which is w hen I used a PWM signal of one channel to control the RED light...
Hi.
Environment : nrf52833, ncs v3.1.1
I am developing device that has PAwR Scanner Role and Extended Advertising for connecting Mobile Phone(nRF Connect APP).
PAwR...
Hello Nordic team,
We are reviewing our nRF54LM20-CAAA (CSP61) hardware design and would appreciate your clarification on several power and RF related points.
DECRF...
We are doing a DFU over BLE with the second MCUboot partition on an external flash. Some times Zephyr can't access the flash after booting, resulting in a bricked device,...
