I'm developing with PCA10040 DK(3.0.0 2022.10), the IDE is SES for ARM 5.42a.
The app is normal after download the application. After a reset or power off and restart, the...
Hi,
We have designed a custom nRF52840 development board based on the XIAO nRF52840 reference schematic. We connected a J-Link debugger to the board and are able to successfully...
Hi,
We have a device using nRF Connect SDK v3.0.2.
The issue is when we try to do FOTA download and we disconnect the WiFi network (power down the router AP) while it...
# nRF54L15 PDM clock runs at ~1/32 of expected (PCLK1M instead of PCLK32M) on a custom board -works on DK
## Summary
On a custom nRF54L15 board, the PDM peripheral...
Hi,
I am using nRF54L15-DK board for development and currently I am trying to talk to an external module via SPI (nRF dev board is the master). I have disabled the external...
I am trying to setup SPI00 as SPI slave on nrf54l15 but not work as expected.
My board configure is like
and c program like
The program intends to use nrf54L15...
I want to use the Softdevice Controller without a crystal on the RTC. I configured my project with
Advertiements look fine, but interaction with a BLE central either throw...
Hi.
I am developing using nRF52820 example source using SDK 17.0.2.
USB and LESC were added using S112.
However, during operation, the following HardFault error occurs...
Hi everyone,
I am trying to integrate the DFU service into my application on order to achieve buttonless OTA DFU but I am not able to implement it so far and I need your...
Hello,
I merged the two projects usbd_cdc_acm_pca10056 (A) and ble_app_hids_mouse_pca10056_s140 (B) by copying all additional contents from A's flash_placement.xml into...
Hello,
I am trying to send data obtained from a SAADC port via BLE using the ble_nus_data_send function. This must happen periodically at frequencies within the Gigahertz...
As we know, NRF9160 supports NB network and has an IMEI number itself. Now I want to know whether I can manage this IMEI number, such as reading, writing or modifying. In...
HI all,I am looking for a help.how to start SPIM RX task immediately delay less than 2us？
I have a SPIM test on 52832 DK board(QFAAE0) with SDK16.0, the MISO pin has connected...
Hello
I have a question about the Bluetooth multipairing function using nrf52832. How do I use this feature? And up to how many connections can I make?
Thank you!
I am going to store some informations into UICR.
In case, wrong data wrote have to correct we need to rewrite it.
I have been searched the forum and the answer shows ...
Hello,
It looks like several people are having issues updating the firmware of the Thingy:91 modem with a simple USB cable.
I personally tried on Windows 10, 8 and 7....
Hello There,
I have problems with the installation of the nRF9160. Started the installation earlier and nRF9160 was detected in nRF Connect/Programmer and I could see memory...
Hi, For my application I was using ESB without softdevice and just recently I wanted to add dfu so I had to add softdevice as well. After adding softdevice I found out that...
I want to convert APP_TIMER_TICKS ms to us.
So i'm using this function.
And, the value of APP_TIMER_CONFIG_RTC_FREQUENCY is
Also this is main code.
And, I...
OS in development environment ：Windows10 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
