Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
While exploring documentaion and trying to learn more about the DFU (and bootloader settings), I found info on how to generate the bootloader settings , which also explains...
I want to measure voltages at all 8 channels but when I am enabling all channels its sending the values once only and after that its not sending anything, my requirement is...
Hi,
We are aware that i2s internally includes hardware double buffering to ensure that the audio is continuous.
Is there any way by which we can avoid double buffering...
Hello,
I developed board with NRF9160 chip and I am facing issue with "at_cmd: Failed to open AT socket (err:-12)", i am not able to communicate with modem. It is not...
Hi
Can I not modify the param the radio project example,and let it run on IEEE802.15.4-2006?
and the demo example run on 2.4GHZ?
I modified two params:
NRF_RADIO-...
Hello,
I'm using nRF52480 Dongle. I executed an Erase All from SEGGER Embedded Studio. My project still works but the LEDs are not blinking anymore. The only way I can have...
Hello nRF Team,
we are using nrf51822 for one of our product. We have implemented firmware update functionality using a secure bootloader library.
After loading the soft...
Hi, I want to distinguish whether the USB is connected to a PC or a power adapter.
For my application, FATFS still needs to work when connected to a power adapter, so it...
Hi Nordic,
Why I cannot directly use segger's "Build and Debug" to download file to nrf52832, after I modify some code?
After I use nrfGo Studio first to program the...
Hi, in the past, there has been discussed several times whether a peripheral can advertise even when it is already connected/bonded. It turned out it could be possible, however...
Hi, We are working on multiple product based on different MCUs (nRF52832 and ESP32). We would like to use the same Nordic BLE DFU for both of the products so that we would...
Planning to run Packetcraft LEAUDIO stack on nRF52840-DK. This is for evaluation and later on for some development on top of it.
Will it be supported. or is it must to have...
Hi,
I am trying to figure out how serial handling works. Specific questions bolded below. To the best I can see, what I think happens when transmitting is:
NRF_SERIAL_DRV_UART_CONFIG_DEF...
Hi,
I have custom board based on nrf91 but i am going to generate 2 SKUs out of it, the first board consists SIP alone mostly running the SLM application, and my second...
I am trying to capture a signal that transmits upon receiving a polling signal along the same wire.
I have frequented this example but still not having any luck (LED toggles...
