Hello, I would like to ask if the latest SDK version supports power management on the FLPR core of the nRF54L15. According to this article, the power consumption is quite...
Hello Nordic Team,
I am reaching out to ask for some advice and/or guidance on how I may debug code that:
1. Is initialized and runs BEFORE main
2. Is part of the zephyr...
Hello,
Hopefully this will be a quick(ish) one since I think I found the answer, but just need confirmation.
To preface (My setup):
nRF9151DK
Modem firmware: mfw_nrf91x1_2...
I have tested the nRF Cloud Multi Service Sample using Quick Start and it works perfectly.
I am trying to build the sample so that I can make small modifications for an...
Hi everyone,
I'm developing a BLE application where I measure throughput between an nRF5340DK acting as peripheral and an nRF52 Dongle as the central (using a Python script...
Hi,
The attached code is based on a sample code from NCS v2.9.1 and creates a LittleFS flash disk on external SPI NOR onboard nrf54L15DK. There is a mismatch in the code...
Hi everyone,
Currently I am routing hardware for an upcoming project using the nRF5340 and it's time for a sanity check.
The goal is that the HW works well enough w/Engineering...
Hi,
I've been trying to set up a SPI <-> USB interface between an FPGA and my PC via the nrf52840 dk. My ultimate goal is to stream 1Mbps+ worth of data, but right now I...
I have a custom characteristic on which I send ASCII strings as notifications similar to NUS. Is there a way to have the Bluetooth Low Energy app in nrfConnect show the data...
I am writing a BLE application on the nRF52832 using S132 v6.0 and SDK 15.2, and my application is using the nrfx_SPIM driver. I find that once I initialize the spim driver...
I am using the nRF52840, SDK 16.0.
I'm attempting to advertise on the coded phy and the 1M phy simultaneously. This works.
I have two phones, one that supports coded...
Hi,
I tried to enable the CMSIS in my CUSTOM Project but I see the following error and the CMSIS configurator is empty. Please guide what would be the possible problem....
Hardware: nRF52840 DK
SDK: 16.0.0
FreeRTOS: 10.0.0
I am attempting to use UARTE1 for a Modbus port. UART0 is already in use for a Command Line Interface. I can set up...
I use Nrf52832 and sdk16.0.Use I2S play sound.
If use:
int16_t sine_table[]= {0,0,23170,23170,32767,32767,23170,0,0,-23170,-23170,-32768,-32768,-23170,-23170};
NRF_I2S...
RTT is a very strange beast. It looks that, depending the printed binary content, the output in the viewer can be displayed - or not. It seems that the rtt viewer acts on...
Hi,
I have converted a project to use the nrf52833 (SES SDK16):
I get a fault with the following:
The build seems to still link to nrf52832_peripherals.h not...
Hi
Recently Openthread has implemented the Enhanced Frame Pending feature and I am using nordic SDK Thread and Zigbee 4.0.0 for my nrf52840 devices.
We want to use "Enhanced...
Hello,
We have a own designed NRF52832 board. If NRF52832 and NRF52811 are pin to pin, we want to use NRF52811 with NRF52832's pcb. Because, NRF52832 bluetooth range is...
hello
I have ble_app_hrs_freertos project for that, I have to make sleep and wake up the services in the project.
my question is that
1) how to sleep the service in...
