HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
I have a question about Makefile template used in all samples in SDK12.x
What is the sense of:
$(foreach target, $(TARGETS), $(call define_target, $(target)))
-include...
When trying to build/run the btle throughput demo I get a device not supported error.
When looking in the Options - Device settings for
the project the Software Packs...
Hi All,
the logging output (NRF_LOG_...) in the SDK17 via the UART works fine on the DK board (only change from the HRS example was the NRF_LOG_BACKEND_UART_TX_PIN has been...
I am using nrf mesh SDK 4.0 with nrf52832 DK and nrf mesh android app , with the light switch exemple , i noticed that a proxy node that was successfully provisioned can be...
Hi,
My aim is on button press in peripheral side ,it should do advertise and sent data from single peripheral to multiple central(total two central).
I am using nrf52810...
Hi,
I am using nRF52840 SoC as a thread device in my application. I want to push data from sensors to cloud. So I need to configure one of my thread devices as border...
Hi Dev team,
I had an issue regarding getting the real time using RTC. I tried to follow the below dev zone blog but the CAL_RTC does not work in my code.
As such, I am...
To the kind attention of Nordic support team,
We are doing EMC pre-tests of our products using your nRF52833 .
At this stage, nRF52833 device is triggering itself a...
Hello.
I am following this tutorial, but unfortunately I am stuck at step 7. I am not sure which characteristic corresponds to the UART RX characteristic value.
I tried...
I've started an asset tracking project at the company that I work at and have tried to use the nrf9160 dev kit for the device tracking part.
I have updated the board firmware...
Hello -
We are working with the nRF52840 and SDK v17.0.0 and tuning our power consumption during System ON sleep. We understand how to wakeup the device using the RTC and...
Hi,
I have encounter a problem that the first button release event is missing if the key is pressed while powering up.
The SDK I am using is nRF5_SDK_17.0.0_9d13099. ...
Hi!
We are using nRF52832-QFAB (B0 variant) in one of our projects, and it works fine and well.
We are now in the process of using the nRF52832-QFAB-E0 in the same build...
how can I work it use nRF5 SDK 17.0.0? On https://developer.nordicsemi.com/nRF5_SDK/pieces/nRF_DeviceFamilyPack/ the newest pack is
NordicSemiconductor.nRF_DeviceFamilyPack...
Hi Support Team,
An error occurs when generating a signed binary file for central_dfu_smp.
Error: Header padding was not requested and image does not start with zeros...
Hello everyone
I success in compilation gpio basic example but I have some problem about bluetooth mesh example.
It show message "undefined reference to `bt_rpmsg_platform_init...
