hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
hi,
I am using nrf52832 with ble multilink(nRF5_sdk_16.0.0) example. I need multiple connections with the peripheral at the same time. is it possible to connect multiple...
Hi.
I'm developing application that is needed to include UARTE Interrupt.
I can drive UART interrupt well(not UARTE), but UARTE is not working.
Here is my code...
Hi, I need to send data larger than 16 bytes on a characteristic. I see that the maximum number of bytes I can send using the indicate function is limited to 16 bytes.
...
I am working with:
NRF52840 boards
nRF Connect SDKwith Zephyr
On Ubuntu
Desired behaviour would be:
Establish connection with Codded PHY
After some time disconnect...
Hello,
I'm working on a firmware for a device that is created using ble proximity example. It is power constrain device and required a connection interval of 30 sec between...
Hi Great Nordic Support Teams:
Our client is developing their BLE products with 5340 , and they'd like to use NCS SDK 1.4.0.
They setting up the NCS environment with...
Hello. I have a issue about fstorage.
first, I using S332 SD and SDK 15.3.0 version and 52832.
Init flow is below:
Log enable -> SD enable -> SD BLE & ANT enable ->...
Hi,
SES is not including the extra cmake build options, i tried prefixing "--" as we do it in west build, note that it works west build "west build -b nrf9160_pca10090ns...
I am attempting to create a custom Buttonless DFU application by building on top of the default example from the SDK. Specifically, I am merging the Buttonless DFU app with...
Hello,
I am new to the BLE world. I have a nrf52 DK and using softdevice 7.0.1
I am trying to to flash the basic blinky example.
In debug mode everything is fine,...
Hi, I have a custom board with an nrf52840 onboard I was able to program the nrf52, but then I executed:
% nrfjprog --eraseall
and,
% nrfjprog --pinreset
and the JLink...
According to the Zephyr documentation here the way to implement an application-specific exception handler is to define k_sys_fatal_error_handler. When I try to do this I get...
Hi. I'm doing the firmware on the custom board.
This board turns on when the button is pressed through the power button circuit. And I created the reset function using NVIC_SystemReset...
Hello, I would like to develop a simple program that sends and receives UART communication through 2 boards.
The example used "examples\peripheral\serial\pca10056\blank...
