I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
On some android phones we have observed that if we try to scan using nRFToolbox for nRF51/ nRF52 controller advertising with UART they do not show up in the scan list. But...
Hello,
I am developing a wireless sensing device using the nRF24L01+ module and I'm planning to use a u.FL connector in my design. I can't seem to find any manufacturer...
Hello,
I am trying to test BLE with SAADC, UART function.
I am complete the ADC test and UART part.
So now, I want to SAADC with BLE and BLE with UART.
The whole connection...
Hi all,
I tried to follow this tutorial to be able to use GDB as debugger but failed right in the beginning because JLinkGDBServer could not connect. Here's the log I get...
Hi , i am using the nrf52dk and i have a switch statement that depending on the case there is a set of enum and i would like to utalised the push button to increase/decrease...
sir, i am attempting to compile a solution from github(nrf calender) but i could n"t.Tell me where should i put the file and how to compile to make it work??
Hello,
I have a question: how can i make applications for Nordic Thingy:91, and upload them to it? (I am a total newbie when it comes to Nordic products and IoT, i am not...
Hi All,
I am developing one project and there we are using ADC (i.e., SAADC in nRF). I have designed the hardware where I am using Capacitor ( C14, 2.2µF) which is connected...
Hi. I have a nRF52840 setup using the PWM driver, and it is outputting a 50Khz pulse 50% duty cycle.
How do I modify the sequence values so that I can modulate this 50Khz...
Dear all,
I would like to implement the IEEE 802.15.4 stack, using the driver inside the SDK for Thread and Zigbee. Unfortunately there aren't any examples ad so everything...
Hi! Please, excuse the probably stupid question but I'm a real newbie. I'm trying to perform a long range coverage test. I got two NRF52840 DK. Got to install both Segger...
Hello all,
I have a question about nRF52832.
What I want to do is increase a number every 20 micro seconds.
In other words, count how much time has passed .
(ex...
I’m developing a wireless sensor based on MINEW nRF52832 modules.
I use SDK 16 and SEGGER embedded studio.
The target is powered by a 3.6V Lithium Thionil battery via...
