Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hi.
In SDK 14.0 examples, there are two examples for pwm.
I analyzed both example.
pwm driver example source looks like that it use pwm peripheral driver source.
And...
Hello,
I would like to sample the battery level of my nrf52832 DK and send it through BLE. I have started from the example ble_app_hrs for SDK12.2 since the service was...
Hi,
Most of the sections of my application are functioning as I want it to, except these two (step 3 and step 4).
Application:
Connect device (with Auto connect...
I noticed while running a Bluetooth scanner app on my iPad, while testing one of my devices, that it was showing someone else's device in the locality.
What I found strange...
Hello!
I have:
nRF52840-Preview-DK (pca10056)
nRF5_SDK_13.0.0_04a0bfd (s140)
I load **nRF5_SDK_13.0.0_04a0bfd\examples\ble_central\ble_app_uart_c\hex\ble_app_uart_c_pca10056_s140...
I have an interrupt coming in every 50-150 microsecs and I want to measure these intervals as precisely as possible.
I tried this with SDK12.2:
APP_TIMER_INIT(0, 5,...
We're trying to bit-bang SWD to program an nRF52832, and we're running into some problems getting the nRF52 to respond. One theory is we're not generating a high enough clock...
i just purchased the www.xcluma.com/bluetooth-4-0-module-NRF51822-2-4G-module-development-board-ble-4-0 this xcluma nrf51822 module , so how can i progarmme it . which IDE...
Hello,
I've noticed the following sentence in s132_nrf52_3.x.x release notes:
"Synthesized low frequency clock source is not tested or intended for use with the BLE...
I'm following the tutorial in the NRF52840 SDK on setting up a Thread Border Router here and I've run into some issues during testing. For one, I'm trying to resolve ipv4...
Hi,
I'm able to successfully enable Access Port protection, either using nrfjprog or by setting NRF_UICR->APPROTECT register to 0xFFFFFF00 in code.
But I have a problem...
Hello,
Since this seems to be a very hard topic to find info about (its very contradictory and confuse) I'd like to ask a Nordic employee directly.
I'm planning to build...
