Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
I expanded the button events based on example ble_peripheral ble_app_hrs by
and everything works fine (button press and button release events for all 4 buttons) till I...
Hi
We found abnormal current waveform when running GPS as 120s fix interval and 10s fix retry.
As below pic, the first plus is A-GPS seraching, from second plus is the...
Hi,
When I used nRF52840 dongle (connectivity_5.1.0_usb_with_s132_5.1.0.uf2 firmware) to receive peripheral device notifications, nRF52840 dongle can only receive 20 bytes...
Hi,
I'm not sure if SES support C++ compiler in nRF9160 project, I did add C++ source in CMakeList:
target_sources(app PRIVATE src/xxx.cpp)
It won't work, Does anyone...
hi,
I use the SDK16.0 ,to develop BLE touchpad on nRF52833,which is should set non-zero value for feature reports . And now,i have a problem,how to implement the FEATURE...
I made a custom board using nRF9160 and tested a very simple program.
However, it consumes high current compared to nRF9160 DK. I measured current flowing on VCC line of...
nRF52832 / SDK 14.2 / SD5.1.0
There might be two configurations to setup a PPI channel to assign some peripheral event to both timer capture & clear task:
nrf_drv_ppi_channel_assign...
Hello all,
Having a smallish problem seeing printk() output on my board. My board is an NRF9160 PCA10090 inspired board. Long story short, I can't see printk() stuff showing...
My application implements a beacon with services, and a buttonless BLE bootloader.
The application can start the bootloader in two ways.
The first method is executed locally...
Hi,
I am in the process of provisioning and configuring a 2-element light switch server node and a common light switch server. I am using the orginal exemple for the provisioner...
I'm attempting to transfer 256K bps (1 244-byte notification every ~7.5ms) using an nRF52840 using Notifications and am not getting close to the necessary bandwidth. I'm getting...
Hi,
We are developing an application requiring the DFU Service on nRF52832.
The implementation of the DFU Service without bonds works very well, but when switching to...
I've been able to connect to our server using the LTE modem sample app.
As shown below, I configure the modem, open a socket, bind the port, and send and receive a small...
As I'm working on debugging a problem where a TLS connection silently fails with no error code, it occurs to me that it would be VERY handy to have a way to connect wireshark...
