I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
We are facing an intermittent issue on an nRF52832–based product using bare-metal Nordic nRF5 SDK (non-NCS, non-Zephyr) BLE implementation.
Observed behavior:
BLE initializes...
Hey,
I am plannign on developing a locator tag and I wanted to find some more precise information on when to use AoA and AoD and if it changes the accuracy drastically....
Hi,
I need to save a 16 bit counter into a retained register.
I cannot use the 2 GPRETREG since they are already used and I cannot write internal flash.
I cannot use...
Hi everyone,
I’m facing a linker issue in NCS v3.0.2 while using the Zephyr HTTP client sample with TLS enabled , and I’m looking for guidance on the correct configuration...
Hi all,
On a BLE project I was working using version 2.5.0 of the VS Code dev environment I was able to set up a partition where I could store non volatile data, such as...
Hi guys,
I've been using the ADC with the internal reference of 0.9V.
However, to increase the scale of the ADC without using the gain 1/4 I've made a revision to the...
Hello,
we are testing the BLE ADV capabilities and also MESH performances on NRF54L15.
We verified that, in conditions of continuous scanning (interval = 30ms), the packet...
Description: I am implementing USB Mass Storage with a FAT filesystem on external MX25UW63 flash (via EXMIF) using the nRF54H20 DK (NCS v3.2.0).
Setup:
Board: nRF54H20...
Hi Nordic Community, I am working with the nRF52833 and I have a question regarding the electrical characteristics of the dedicated USB signal pins (D+ and D-) when the USB...
I thought that the nRF21L01 had been obsoleted and replaced with the nRF21L01+, but digikey doesn't list the + version but still shows the old one for sale. Has the part been...
I'm sending HCI command LE Set Transmit Power Reporting Enable with both local and remote reporting requested.
The Bluetooth Core Specification says "If the Remote_Enable...
On nRF54L15 DK (CPUAPP) the app boots and advertises fine, I bound my phone using nrfconnect but when I reboot the DK and try to reconnet using nrfconnect, the device hangs...
I have a new nrf9160dk board that I will be using for a BLE customer application. I am using zephyr/samples/bluetooth/hci_uart SDK V3.2.0 to be loaded into the nRF52840 in...
Hi Nordic
We would like to be able to read out the serial number off our devices, without connecting to them,
We have not enabled RFID on the product, but would like to...
