Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Where is the provisioning configuration data getting stored ?
1. EEPROM
2. Any other non volatile memory
Is it getting stored in external chip to nrf52833 or inside...
Hello there!
I'm quite new to the topic and just tried to dig into it a bit, so I'm sorry if I didn't get all things yet about the nRF5280 Dongle :) .
Right now, I'm following...
Hi all,
Using the thread CLI example (on a PCA10056 board) as a starting point I would like nodes to connect automatically to a thread mesh when booting. I then want to...
I use the following example source code to test NFC pairing.
Example source code for NFC: nRF5_SDK_17.0.2_d674dde\nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\experimental...
Hi
thank you very much for your paying attention.
Yes the peripherial_uart sample seems to be a good choice for my project. But Uart 0 pins didn't come out on GPIO connector...
Hi,
We are trying to create a network using 20 movesense sensors and BWG840 Fanstel gateway acting as the central. The gateway is running a modified ble app uart multilink...
I'm a beginner in BLE applications, and I'm having trouble with connecting nRF toolbox application
I wanted to use UART function provided in nRF toolbox.
But, an e rror...
Hi,
I wish to run an existing project in Segger embedded studio for its debug capabilities (Currently the project runs in VS code).
I'm using the nrf52832, running a bare...
I'm trying to add the unity test integration to our project, but failing to build, since the project has a dependency on nrf_oberon
For the sake of completeness, the project...
I'm having trouble connecting Thingy:91 to cloud.
I've installed both the modem and HEX image in the board successfully.
I've added the SIM card successfully to the...
I've had intermittent issues with the nrf9160 modem using mfw 1.3.0 with an iBASIS SIM getting stuck in "searching" state when first powering on. The symptoms are similar...
I am using a nrf_drv_twi_tx() and nrf_drv_twi_rx() for a simple I2C transaction but I'm noticing a strange behavior.
If I don't use APP_ERROR_CHECK(err_code); right after...
Hi,
We are developing a flutter mobile app, for Actility/Abeeway (chips from Avnet Silica) using flutter pluggin that relies on the Android SDK. In some situations (after...
Hello,
I am using NCS v1.6.0, nRF Connect for Desktop v3.7.0, and the Bluetooth Low Energy app v2.5.1 (part of nRF Connect for Desktop). I am using the nRF52840 Dongle with...
