Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
For a customer we're trying to see if we can build an IoT solution with nrf9160 to periodically send a status update to the cloud. Unfortunately, the devices are typically...
Hi everyone,
I suppose that this is a simple question but I cannot figure out what I am doing wrong. I am trying to set up an interrupt for a GPIO
I call the createInterrupt...
Hi ,
I am working nrf9160 project. I am facing error while downloading the project.
I followed the ticket - https://devzone.nordicsemi.com/f/nordic-q-a/50422/how-send...
Hello together, I am trying to work with the SEGGER software and would like to test it with a Sample from the nRF Connect SDK.
I've installed it over the Toolchain application...
Hi, I want to transfer 900KB file from mobile to NRF52.
I am using nRF5_SDK_15.3.0_59ac345. - Can you guide me for that? - How BLE receives a bin file from DFU via the NRF...
Hello, Following is my development environment IDE: Segger SDK: 16 SoftDevice: S132 Right now, we are trying to merge the following two examples. - examples/peripheral/nrf5...
I'm looking for a simple demonstration application that can run on the nRF52 Dev board and communicate with the default Thingy52 firmware. My plan is to get this working on...
I'm trying to read the Device Name from address 0x21 on a BQ40Z80 fuel gauge, using my nRF9160 chip, connected via SMBus.
When polling the address space, I nicely get an...
I'm using Ubuntu 20.04, SES 4.52c, SDK 16 nRF52840 DK board.
I'm going to need to use the PWM driver to supply clock pulses to an I2S microphone and the I2S peripheral running...
Hello all, I've run into a weird problem that hopefully someone has a clue. My environment: - PCA10040A, nRF52832 - sdk 17.0 - softdevice s132_nrf52_7.0.1_softdevice.hex ...
Hi:
I have a set of 2x Thingy:91 and 2x Thingy:52
I want to make a setup where the devises work in line over a longer distance. T91-T52-T52-T91 is that possible all working...
I want to run the realtime counter RTC2 with softdevice S132 WITHOUT an interrupt handler. I have no purpose for an RTC2 interrupt handler in my code, as I simply want to...
Hello,
i have issues getting the new softdevice into my product.
nRF52832 with 512kB Flash and 64kB RAM.
Currently i use s132_v6.1.0, a bootloader and an application...
