Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
Hallo,
we are using the nrf5340 and the ncs Version 2.6.1.
I activated the software downgrade protection as described here Downgrade protection (nordicsemi.com) .
Then...
I just received a new 54L15DK and was attempting to port a simple 5340 project to it. The first time I attempted to flash it, it _looked_ like it was successful:
[1 0/10...
The subject issue is documented here as " NCSDK-20567: Partitioning limitation with MCUboot swap move": This issue has been open for while. These two DevZone tickets refer...
In our application we using nrd5340-nrf7002, application flow is wakeup->wifi connect->NTP time get->TCP server connect->wifi shutdown->idle->wakeup..... We are encountering...
Hi Nordic
I am curious how to test nRF54L15 BLE sensitivity and Blocking.
I am currently using:
1) nRF Connect For Desktop" v5.1.0
2) Direct Test Mode v2.4.0
...
Hi y'all.
I've been developing in Zephyr NRF52840. My code is based in Central_HR_Coded (SDK 2.6.1, Toolchain 2.7.0). I had some issues with the bt_conn_disconnect function...
Hi, I'm new to this product and currently working on the Nordic Thingy:91X and have encountered some issues that I need help with. below is the details from the serial
monitor...
Hi,
I am developing an application with LTE-M connectivity to nRF Cloud. Our previous SIM apparently supported auto-APN provisioning, we did not have to set the APN, the...
Hello,
I bought brand new Thingy53, but Thingy53 turn off during deployment and can not connect to BLE, becuase it turns off. Please assist me if possible.
Hi,
I test my nrf54l15 module(disconnect every gpio with outside),the sleep current was 3uA,seens can't not achieve 0.6uA as the datasheet said.
The nrf54L15's markcode...
I am experimenting with sampling IQ at the payload in AoD mode. Are there any differences in the configuration of the receiver in AoA mode as seen in the direction finding...
Dear DevZone,
I believe I am quite familiar to this forum due to my ongoing Wi-Fi issues with SDK 2.6.1 To determine if a newer SDK version will resolve these problems,...
Hi,
I still try to configure Nordic-Zepyr build for a nrf5340, with a BLE stack and MCUBoot as the bootloader. The application will receive image updates over MQTT and store...
Hello everyone,
I'm having an issue with my nRF52840 Dongle. I can detect the device with nrfutil device list command, which shows:
> nrfutil device list DC1D9FD62EC5...
