Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I added my own overlay to the website routine "ncs-fund\v2.8.x-v2.7.0\l5\l5_e1_sol". The contents are as follows
/////////////////////////////////////////////////...
Hi，
My VSCode extension is not working now. could you please give me some advice? thanks!
1.<Manange toolchains> could not display and select the toolchanis version
...
Working to comply with EN 300 328 V2.2.2 by reducing Media Utilisation to <10% on my FHSS system. I've been told that over-the-air, the NRF24L01+ actually transmits 9 bits...
I'm trying to get the settings api working with multiple partitions using little FS. Some of the implementation is specific to Nordic and was hoping to get an example of how...
We have developed a custom board with an external SPI flash, which I have tested and it works.
We want to use OTA over BLE, so we have added MCUboot to the project, which...
Hi all,
I am trying to decide what DK I should go for if I want to test out the BLE Direction Finding capabilities of the SoC.
I am interested in getting the nRF5340-DK...
I'm using an nRF52832 with SDK v15.3.0 configured as an SPI slave in mode 0, with a master clock speed of 1.25 Mbps. My SPI pin assignments are:
- CS -> P0.06 - MISO ->...
I built an application and tested it with DK, and it worked well. I then created a custom PCB and attempted to flash the application, but the BLE part is failing with the...
Hello,
Platform: nRF54L15, SDK 2.9, VS Code
Our application is Matter + BLE (like NUS) based door lock application. A BLE custom service (adapted from NUS) is used to...
Hello,
I am currently learning Zephyr via the Developer Academy in preparation for an upcoming project that will use an nRF9151 and a Nordic BLE module. I will need to write...
Hi!
First of all, sorry but I will not be able to provide anything to re-create the bug... I did modify the code that may have made it happen in the first place quite a...
Hi, my two nRF52840 devices are set as peripheral and central respectively. Both devices use nRF52 SDK.
I try to update the PHY in the two devices, after they are connected...
Hi,
I was playing with my development software in VS Code everything was OK apart from the Cmake error message.
Once I had to restart my computer I couldn't build my...
