Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Is there any guidance on zigBee OTA? What are the similarities and differences between ZigBee OTA and BLE OTA? Could you please tell me what I need to pay attention to during...
Today I received my first CMSIS-DAP debug probe (Pitaya link) and tried to integrate it into my development environment. Unfortunately, I must have broken my Pitaya Go (Nordic...
Hello,
I've been very slowly gearing up towards developing for the nRF9160. I'm going through the "nRF Connect SDK Tutorial"
https://devzone.nordicsemi.com/nordic/cellular...
For example, I'd like to add at_cmd_parser to my project. It's under /ncs/nrf/lib/at_cmd_parser.
My project is out-of-tree in its own directory. Initially I tried add to...
Hello,
I am using example code of LIS2DH ac celerometer sensor with nRF SDK v1.3.1. Building the example code I am getting macro error in devicetree.h file as mentioned...
Hello,
I am using PPK 1 kit with nRF52 DK. The system is used to measure the power on nRF52840 DK using DUT mode. The system was working just fine until I started receiving...
Hi
I'm trying to use the nrfx TWI Slave function with IRQ (No Poll), but there is no clean code available I found.
I'm using the following code:
But even if I can...
Hello,
I am using NRF9160 running the Serial LTE Modem application in NCS 1.5.0. When connecting with AWS IoT over a secure MQTT connection the maximum MQTT packet size...
I'm using nRF5340 to provide Bluetooth connection to other devices. Almost all Android devices connect correctly, for example: Samsung S21, LG G8X, Xiaomi Mi Mix 2. However...
Greetings,
I am using nRF52832 QFAA E0 in my development stages and found no issues regarding the architecture I have been using. Architecture:
DFU is built separately...
Hi, I am fairly new to the NRF and was wondering if there was a way to increase the sampling rate to 100Hz. I have used the ble_app_uart example to configure this code:
...
Hi,
I am using nrf52832 DK.
SDK17.0.2 and Softdevice S132
I have a ESP32 C3 module as a central device which scans for BLE5 devices.
I have kept the nrf52832 DK...
Hi there,
I was wondering, is there any project or plan to use the nRF9160 as a modem with standard ethernet interface ? The ethernet interface could be either
- RMII...
Hello, I currently have nrf9160 devices deployed running nrf connect sdk v1.3.0 that fails to reboot into the secondary image. It specifically happens when I try to send a...
Hello. I orignally had an expired SIM card that came with my device, so I got a new SIM card to setup with the Thingy:91. These come with an EID of 19 digits, but no ICCID...
