Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
Hi there,
Under lesson 3 of devAcademy
https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-3-adding-custom-board-support/
There is an...
Hello,
I noticed that the newest nrf tooblox app keeps crashing after I connect to a device with NUS services. If I connect to an unsupported device, it just informs me...
Dears,
I made module with nRF52832. And I made also custom board with the module.
And then I tried to write FW(ble_app_uart_c_pca10040_s132.hex) but timeout error occurred...
I am trying to make a custom board device tree for evaluation of some new parts and am struggling. I have attached the Schematic as reference sine this is only for part discovery...
Hello,
I am developing a product with the nrf52840 + npm1100 for battery management. I added a usb connection for serial communication, connected as suggested by the reference...
NCS 2.7.0
nrf52840
I'm currently porting software that was originally developed for nrf52832 on NRF5 SDK to run on Zephyr. I am currently on a deadline to delivery a prototype...
I am trying to run the sample using NCS v2.5.0. This is what happens on the console when I try to connect from the dongle, when running the Test Procedure:
The discovery...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
Hello,
I recently migrated to SDK version 3.2.0-preview, which supports Matter 1.4.x.
When I use ZAP and add a new endpoint to the light_bulb example under the name Electrical...
Hi I'm trying to communicate with ICM45686 using nRF54H20 and SPI CLK, MISO, MOSI state appear correct but CS pin is not asserting/deasserting following it the scope capture...
Regarding the nRF54L15-DK development board and its use with BlueZ on an Ubuntu virtual machine: After flashing the hci_uart example onto the nRF54L15-DK board, I used the...
I’m working on a project using the nRF54L15 SoC together with the nPM1300 Power Management IC . In my hardware setup:
BUCK2 output from the nPM1300 is connected to the...
Hello, I am facing an issue in nrf52dk (nrf52832dk). Whenever I access i2c0 bus for the controller it works fine but whenever i switched on the i2c1, it starts giving me device...
