Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi,
When I want use nrfjprog to program my NRF52, I have a problem.
This why I write to program my nerf : nrfjprog -f nrf52 --program _build/astronaut.hex --sectorerase...
Hello,
Is there example code on how to get NRF_SAADC_INPUT_VDDHDIV5 working? When I do nrfx_saadc_init(), I get NRF_ERROR_INVALID_STATE.
Same code works fine with normal...
I am using nrf5340 and icm20948 for our development. i had initialized things as shown in code attached.
this work fine for me. but when i am uncommenting rc |= inv_icm20948_enable_sensor...
Is there any guidance on zigBee OTA? What are the similarities and differences between ZigBee OTA and BLE OTA? Could you please tell me what I need to pay attention to during...
Today I received my first CMSIS-DAP debug probe (Pitaya link) and tried to integrate it into my development environment. Unfortunately, I must have broken my Pitaya Go (Nordic...
Hello,
I've been very slowly gearing up towards developing for the nRF9160. I'm going through the "nRF Connect SDK Tutorial"
https://devzone.nordicsemi.com/nordic/cellular...
For example, I'd like to add at_cmd_parser to my project. It's under /ncs/nrf/lib/at_cmd_parser.
My project is out-of-tree in its own directory. Initially I tried add to...
Hello,
I am using example code of LIS2DH ac celerometer sensor with nRF SDK v1.3.1. Building the example code I am getting macro error in devicetree.h file as mentioned...
Hello,
I am using PPK 1 kit with nRF52 DK. The system is used to measure the power on nRF52840 DK using DUT mode. The system was working just fine until I started receiving...
Hi
I'm trying to use the nrfx TWI Slave function with IRQ (No Poll), but there is no clean code available I found.
I'm using the following code:
But even if I can...
Hello,
I am using NRF9160 running the Serial LTE Modem application in NCS 1.5.0. When connecting with AWS IoT over a secure MQTT connection the maximum MQTT packet size...
I'm using nRF5340 to provide Bluetooth connection to other devices. Almost all Android devices connect correctly, for example: Samsung S21, LG G8X, Xiaomi Mi Mix 2. However...
Greetings,
I am using nRF52832 QFAA E0 in my development stages and found no issues regarding the architecture I have been using. Architecture:
DFU is built separately...
Hi, I am fairly new to the NRF and was wondering if there was a way to increase the sampling rate to 100Hz. I have used the ble_app_uart example to configure this code:
...
Hi,
I am using nrf52832 DK.
SDK17.0.2 and Softdevice S132
I have a ESP32 C3 module as a central device which scans for BLE5 devices.
I have kept the nrf52832 DK...
