Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
I would like to source a compact BLE board to act as a lock controller developed with with a matching transceiver for use in a fob and an app.
It would toggle the pio and...
Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello Nordic Team,
I am using the nRF5340 Audio DK and I want to implement a simple audio loopback — where the board captures voice from the on-board PDM microphone and...
hello~
nPM1304 nominal sleep mode 500nA (it is still uncertain whether the buck converter can operate?)
Can't the sleep mode be lower than 500nA?
best regards
sam
I'm following the Lesson 9, Exercise 2: DFU over USB - Adding External Flash from the Nordic Academy: Tutorial Link
SoC: nrf54l15
SDK version: 3.0.2
Toolchain version...
Hi,
I’m using a custom nRF5340 board , and I recently migrated my project from nRF Connect SDK v2.9.0 to v3.1.1 .
The same project compiled and worked fine on v2.9.0,...
Hello,
I'm interested in nRF54L10 SoC, in Mouser and DigiKey I see that I can buy it in this package: QFN48 (QFAA). However in the datasheet it shows this package QFN40...
Hi,
I’m currently working with the nRF54L15 DK using the Channel Sounding Initiator with Ranging Requestor sample from the latest nRF Connect SDK. The setup runs successfully...
Dear nRF experts.
I am using the radio_test sample with SDK3.10
We used radio_test to add UART commands to control the on/off of all GPIOs for pin verification. We found...
I'm currently looking for a high-speed data transmission and reception solution that requires wifi (NRF7002) throughput, but I don't want to transmit data via wifi. It should...
I'm using nRF Connect for Visual Studio Code, working on a project that has worked great in the past, but I'm getting error messages now when attempting to flash any board...
Hi,
We are using the PMIC in our smart ring where we have limitations of number of components used and specially the height of the components used. Here, the inductor...
Dear Nordic Support Team,
Hope this email finds you well. I am currently developing a Matter-enabled device using the Nordic nRF Connect SDK, and I’ve encountered a question...
Hi,
I just got a power profiler kit II and I want to use it in an battery based application, where there is also the possibility that current will flow in the opposite direction...
I am using the nRF54L10 chip with NSC-V3.0.0, and I encounter an issue when using uart21 (p2.07–p2.08). If RTT is connected, UART transmission and reception both work normally...
Why doesn't the scan_evt_handler get called in the ble_app_uart_c sample under nRF5_SDK_17.0.2_d674dde conditions? I've tried various things, but neither scan_evt_handler...
Hi,
We are testing a custom board based on the nRF5340 that drives an RGB LED strip using the TI TLC5947 LED driver.
The TLC5947 has an OE (Blank) pin that disables/enables...
