Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
Hey,
I’m currently evaluating DECT NR+ using two nRF9151 DKs with the nRF Connect SDK v2.9.0.
According to the ETSI specification (ETSI TS 103 636-4 V2.1.1), the Physical...
While testing CoAP with NB-IoT I normally get PSM (sleep) delay = 20s before PSM mode is set (0.5mA with UART enabled), but after awhile PSM delay increases to ~4.5min (at...
Hi,
I recently added FOTA support on my project which runs on nRF5340 + nRF7002. I am currently working on a devboard, nRF7002DK.
Previously, I was running the project...
Since I need zephyr version 4.0 or newer, I tried updating my project to the nRF Connect SDK v3.0.0 as well as the toolchain. I know that they are not fully released yet....
Hello,
Currently the nrf-connect extension offers board targets under build configuration. These are categorized as "Nordic SoC", "Custom boards", "All". As I have understood...
After updating to 3.0rc2 from 2.9.1 Mesh example fail to build. Crypto related issues.
yml modules -
- name : nrf remote : ncs repo-path : sdk-nrf revision : 52921acad685bb3815af94d9a3a4a11ad209fcd0...
For nRF7002 the VBAT range is 2.9 - 4.5V.
Will the supply voltage used, affect the WiFi performance?
In other words, will one get the same performance by using 2.9V supply...
I am using XiP with partial code running from MX25. I am facing issue where I am getting hard faults when Erase is happening and at the same time the ISR from XiP region is...
I have a custom nRF52832 board with outputs on P0.07 P0.08 P0.09 P0.10 and I want to write to them. 7&8 are working ok but 9&10 are not.
Let me emphasise THE BOARD IS WORKING...
We are currently working on a project based on Enhanced ShockBurst (ESB) and would like to use Front-End Module (FEM) support with the nRF21540.
In your Enhanced ShockBurst...
I need to put my external Flash into the deepest possible sleep mode possible,
I saw this api in flash.c in Zephyr, I am using the
( flash_ex_op ( const struct device...
Hi,
I am trying to integrate Buttonless DFU in my application. I have implemented all the steps mentioned in this tutorial.
Getting started with Nordic's Secure DFU...
