I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi, I'm having Bluetooth LE peripheral nus code which works fine with v2.7.0 with nrf52840DK (I can connect with an Android App and stream data etc): Changing the build configuration...
NCS 2.7
NRF52840
Building with sysbuild, MCUBOOT, and 2 different applications (mfg and end-user)
My custom board includes a sensor fusion IMU from bosch. The firmware...
Hello,
I want to test nRF21540 EK with a nRF5340 DK.
I am using ncs 2.7 , and don't want to use sys build . I want to use child image/ hci_ipc .
I modified ncs/zephyr...
We have devices that have low signal so they have to reconnect to AWS a lot. We have a watchdog timer with a 100s timeout that we feed every 10 seconds in the control loop...
Hello everyone!
I am having trouble with my current setup and I would like to ask you for your advice.
I am developing a central station featuring nRF5340+nRF7002. This...
I generated an overlay file with the following info:
and there is my main.c file:
However, when I tried to debug my code to understand what was wrong, I got the...
Hi,
I am using nrf52840 and implemented shell interface. I have testing it over uart and uart over usb. At any given moment it can be enabled over 1 interface in device...
In this exercise the PWM terminology is used incorrectly, confusing the pwm pulse width (nsecs) and duty cycle (percentage). I know the difference from 40+ years of designing...
Hi,
I am new to nrf and have started working with nrf5340 audio dk board. I am using VS Code for programming and the SDK version used is v2.6.1.
I tested the board with...
Is my following operation, first output high, and then configure as input, and then in the output low, this time in the output low here nrf_gpio_cfg_output(IO_PIN_C[j]); This...
1. Setting the IWindow value smaller than Interval will save power.
2. Setting the Interval and Window values to the same will increase the chances of scanning and being...
Hi,I have been using nrf5340 audio DK Board to access the I2S .I am using SPH0645 mic with that i need to get mic data .I am getting mic data continuously but sure that I...
if you see over here data out line is green and prepuol color is data in line first we are sending the 9F so that it will give the manufacture id like this ef and 40 and 0x16...
Hello Support-Team! We are designing a system, where we need to maintain some settings using shell commands (we plan to develop our own set of customised commands). Our platform...
